PIC16LF145X Datasheet, PDF (9/38 Pages) Microchip Technology – PIC16(L)F145X Memory Programming Specification

PIC16(L)F145X
REGISTER 3-3:
CONFIGURATION WORD 1
R/P-1
R/P-1
FCMEN
IESO
bit 13
R/P-1
CLKOUTEN
R/P-1
CP
bit 7
R/P-1
MCLRE
R/P-1
PWRTE
R/P-1
R/P-1
WDTE<1:0>
Legend:
R = Readable bit
-n = Value after Bulk Erase
P = Programmable Bit
‘1’ = Bit is set
R/P-1
R/P-1
BOREN<1:0>
U-1
—
bit 8
R/P-1
R/P-1
FOSC<2:0>
R/P-1
bit 0
U = Unimplemented bit
‘0’ = Bit is cleared
bit 13
bit 12
bit 11
bit 10-9
bit 8
bit 7
bit 6
bit 5
bit 4-3
bit 2-0
FCMEN: Fail-Safe Clock Monitor Enable bit
1 = Fail-Safe Clock Monitor is enabled
0 = Fail-Safe Clock Monitor is disabled
IESO: Internal/External Switchover bit
1 = Internal/External Switchover mode is enabled
0 = Internal/External Switchover mode is disabled
CLKOUTEN: Clock Out Enable bit
1 = CLKOUT function is disabled. I/O or oscillator function on CLKOUT pin.
0 = CLKOUT function is enabled on CLKOUT pin
BOREN<1:0>: Brown-out Reset Enable bits⁽¹⁾
11 = BOR enabled
10 = BOR enabled during operation and disabled in Sleep
01 = BOR controlled by SBOREN bit of the PCON register
00 = BOR disabled
Unimplemented: Read as ‘1’
CP: Code Protection bit⁽²⁾
1 = Program memory code protection is disabled
0 = Program memory code protection is enabled
MCLRE: MCLR/VPP Pin Function Select bit
If LVP bit = 1:
This bit is ignored.
If LVP bit = 0:
1 = MCLR/VPP pin function is MCLR; Weak pull-up enabled.
0 = MCLR/VPP pin function is digital input; MCLR internally disabled; Weak pull-up under control of WPUA register.
PWRTE: Power-up Timer Enable bit⁽¹⁾
1 = PWRT disabled
0 = PWRT enabled
WDTE<1:0>: Watchdog Timer Enable bit
11 = WDT enabled
10 = WDT enabled while running and disabled in Sleep
01 = WDT controlled by the SWDTEN bit in the WDTCON register
00 = WDT disabled
FOSC<2:0>: Oscillator Selection bits
111 = ECH: External Clock, High-Power mode: on CLKIN pin
110 = ECM: External Clock, Medium-Power mode: on CLKIN pin
101 = ECL: External Clock, Low-Power mode: on CLKIN pin
100 = INTOSC oscillator: I/O function on OSC1 pin
011 = EXTRC oscillator: RC function on CLKIN pin
010 = HS oscillator: High-speed crystal/resonator on OSC1 and OSC2 pins
001 = XT oscillator: Crystal/resonator on OSC1 and OSC2 pins
000 = LP oscillator: Low-power crystal on OSC1 and OSC2 pins
Note 1: Enabling Brown-out Reset does not automatically enable Power-up Timer.
2: Once enabled (CP = 0), code protection can only be disabled by bulk erasing the device.
 2011-2012 Microchip Technology Inc.
Advance Information
DS41620C-page 9