DSPIC30F6015-30I-PT Datasheet, PDF (42/236 Pages) Microchip Technology – High-Performance, 16-Bit Digital Signal Controllers

dsPIC30F6010A/6015
5.1 Interrupt Priority
The user assignable Interrupt Priority (IP<2:0>) bits
for each individual interrupt source are located in the
Least Significant 3 bits of each nibble within the IPCx
register(s). Bit 3 of each nibble is not used and is read
as a ‘0’. These bits define the priority level assigned
to a particular interrupt by the user.
Note:
The user selectable priority levels start at
0, as the lowest priority and level 7, as the
highest priority.
Since more than one interrupt request source may be
assigned to a specific user-specified priority level, a
means is provided to assign priority within a given level.
This method is called “Natural Order Priority”.
Natural Order Priority is determined by the position of
an interrupt in the vector table, and only affects
interrupt operation when multiple interrupts with the
same user-assigned priority become pending at the
same time.
Table 5-1 lists the interrupt numbers and interrupt
sources for the dsPIC DSC devices and their associated
vector numbers.
Note 1: The Natural Order Priority scheme has 0
as the highest priority and 53 as the
lowest priority.
2: The Natural Order Priority number is the
same as the INT number.
The ability for the user to assign every interrupt to one
of seven priority levels means that the user can assign
a very high overall priority level to an interrupt with a
low natural order priority.
TABLE 5-1: INTERRUPT VECTOR TABLE
INT Vector
Number Number
Interrupt Source
Highest Natural Order Priority
0
8 INT0 – External Interrupt 0
1
9 IC1 – Input Capture 1
2
10 OC1 – Output Compare 1
3
11 T1 – Timer1
4
12 IC2 – Input Capture 2
5
13 OC2 – Output Compare 2
6
14 T2 – Timer2
7
15 T3 – Timer3
8
16 SPI1
9
17 U1RX – UART1 Receiver
10
18 U1TX – UART1 Transmitter
11
19 ADC – ADC Convert Done
12
20 NVM - NVM Write Complete
13
21 SI2C – I²C™ Slave Interrupt
14
22 MI2C – I²C Master Interrupt
15
23 Input Change Interrupt
16
24 INT1 – External Interrupt 1
17
25 IC7 – Input Capture 7
18
26 IC8 – Input Capture 8
19
27 OC3 – Output Compare 3
20
28 OC4 – Output Compare 4
21
29 T4 – Timer4
22
30 T5 – Timer5
23
31 INT2 – External Interrupt 2
24
32 U2RX – UART2 Receiver
25
33 U2TX – UART2 Transmitter
26
34 SPI2
27
35 C1 – Combined IRQ for CAN1
28
36 IC3 – Input Capture 3
29
37 IC4 – Input Capture 4
30
38 IC5 – Input Capture 5
31
39 IC6 – Input Capture 6
32
40 OC5 – Output Compare 5
33
41 OC6 – Output Compare 6
34
42 OC7 – Output Compare 7
35
43 OC8 – Output Compare 8
36
44 INT3 – External Interrupt 3
37
45 INT4 - External Interrupt 4
38
46 C2 – Combined IRQ for CAN2
39
47 PWM – PWM Period Match
40
48 QEI – QEI Interrupt
41
49 Reserved
42
50 Reserved
43
51 FLTA – PWM Fault A
44
52 FLTB – PWM Fault B
45-53 53-61 Reserved
Lowest Natural Order Priority
DS70150B-page 40
© 2006 Microchip Technology Inc.