DSPIC33FJ32GP302_12 Datasheet, PDF (348/436 Pages) Microchip Technology – 16-bit Digital Signal Controllers (up to 128 KB Flash and 16K SRAM) with Advanced Analog

dsPIC33FJ32GP302/304, dsPIC33FJ64GPX02/X04, AND dsPIC33FJ128GPX02/X04
TABLE 30-11: ELECTRICAL CHARACTERISTICS: BOR
DC CHARACTERISTICS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
Param
No.
Symbol
Characteristic
Min⁽¹⁾ Typ Max⁽¹⁾ Units
Conditions
BO10
VBOR BOR Event on VDD transition high-to-low 2.40 — 2.55
V
VDD
Note 1: Parameters are for design guidance only and are not tested in manufacturing.
TABLE 30-12: DC CHARACTERISTICS: PROGRAM MEMORY
Standard Operating Conditions: 3.0V to 3.6V
DC CHARACTERISTICS
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
Param
No.
Symbol
Characteristic
Min Typ⁽¹⁾ Max Units
Conditions
Program Flash Memory
D130a EP
Cell Endurance
10,000 —
— E/W -40° C to +125° C
D131 VPR VDD for Read
VMIN —
3.6
V VMIN = Minimum operating
voltage
D132B VPEW VDD for Self-Timed Write
VMIN —
3.6
V VMIN = Minimum operating
voltage
D134 TRETD Characteristic Retention
20
—
— Year Provided no other specifications
are violated
D135 IDDP
Supply Current during
Programming
—
10
— mA
D136a TRW Row Write Time
1.32 — 1.74 ms TRW = 11064 FRC cycles,
TA = +85°C, See Note 2
D136b TRW Row Write Time
1.28 — 1.79 ms TRW = 11064 FRC cycles,
TA = +125°C, See Note 2
D137a TPE
Page Erase Time
20.1 — 26.5 ms TPE = 168517 FRC cycles,
TA = +85°C, See Note 2
D137b TPE
Page Erase Time
19.5 — 27.3 ms TPE = 168517 FRC cycles,
TA = +125°C, See Note 2
D138a TWW Word Write Cycle Time
42.3 — 55.9 µs TWW = 355 FRC cycles,
TA = +85°C, See Note 2
D138b TWW Word Write Cycle Time
41.1 — 57.6 µs TWW = 355 FRC cycles,
TA = +125°C, See Note 2
Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.
2: Other conditions: FRC = 7.37 MHz, TUN<5:0> = b'011111 (for Min), TUN<5:0> = b'100000 (for Max).
This parameter depends on the FRC accuracy (see Table 30-19) and the value of the FRC Oscillator
Tuning register (see Register 9-4). For complete details on calculating the Minimum and Maximum time
see Section 5.3 “Programming Operations”.
TABLE 30-13: INTERNAL VOLTAGE REGULATOR SPECIFICATIONS
Standard Operating Conditions (unless otherwise stated):
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
Param
No.
Symbol
Characteristics
Min Typ Max Units
— _{CEFC External Filter Capacitor}
Value⁽¹⁾
4.7
10
—
μF
Note 1: Typical VCAP voltage = 2.5V when VDD ≥ VDDMIN.
Comments
Capacitor must be low series
resistance (< 5 Ohms)
DS70292G-page 348
© 2007-2012 Microchip Technology Inc.