PIC16F722 Datasheet, PDF (217/302 Pages) Microchip Technology – 28/40/44-Pin Flash Microcontrollers with nanoWatt XLP Technology

PIC16F72X/PIC16LF72X
23.3 DC Characteristics: PIC16F72X/PIC16LF72X-I/E (Power-Down) (Continued)
PIC16LF72X
PIC16F72X
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Param
No.
Device Characteristics
Min.
Typ†
Max.
+85°C
Max.
+125°C
Units
VDD
Conditions
Note
Power-down Base Current (IPD)⁽²⁾
D027
— 0.06 0.7
5.0
μA
1.8 A/D Current (Note 1, Note 4), no
— 0.08 1.0
5.5
μA
3.0 ^{conversion in progress}
D027
—
6
10.7
18
μA
1.8 A/D Current (Note 1, Note 4), no
—
7
10.6
20
μA
3.0 ^{conversion in progress}
—
7.2 11.9
22
μA
5.0
D027A
— 250 400
—
μA
1.8 A/D Current (Note 1, Note 4),
— 250 400
—
μA
3.0 ^{conversion in progress}
D027A
— 280 430
—
μA
1.8 A/D Current (Note 1, Note 4,
— 280 430
—
μA
3.0 ^{Note 5), conversion in progress}
— 280 430
—
μA
5.0
D028
—
2.2
3.2
14.4
μA
1.8 Cap Sense Low Power
—
3.3
4.4
15.6
μA
3.0 ^{Oscillator mode}
D028
—
6.5
13
—
8
14
21
μA
1.8 Cap Sense Low Power
23
μA
3.0 ^{Oscillator mode}
—
8
14
25
μA
5.0
D028A
—
4.2
6
—
6
7
17
μA
1.8 Cap Sense Medium Power
18
μA
3.0 ^{Oscillator mode}
D028A
—
8.5 15.5
23
μA
1.8 Cap Sense Medium Power
—
11
17
24
μA
3.0 ^{Oscillator mode}
—
11
18
27
μA
5.0
D028B
—
12
14
—
32
35
25
μA
1.8 Cap Sense High Power
44
μA
3.0 ^{Oscillator mode}
D028B
—
16
20
—
36
41
31
μA
1.8 Cap Sense High Power
50
μA
3.0 ^{Oscillator mode}
—
42
49
58
μA
5.0
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1:
The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral Δ current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
3: Fixed Voltage Reference is automatically enabled whenever the BOR is enabled
4: A/D oscillator source is FRC
5: 0.1 μF capacitor on VCAP (RA0).
© 2009 Microchip Technology Inc.
DS41341E-page 217