|
DSPIC33FJ16GP101_13 Datasheet, PDF (1/386 Pages) Microchip Technology – 16-Bit Digital Signal Controllers up to 32-Kbyte Flash and 2-Kbyte SRAM | |||
|
dsPIC33FJ16(GP/MC)101/102 AND
dsPIC33FJ32(GP/MC)101/102/104
16-Bit Digital Signal Controllers
(up to 32-Kbyte Flash and 2-Kbyte SRAM)
Operating Conditions
⢠3.0V to 3.6V, -40ºC to +125ºC, DC to 16 MIPS
Core: 16-bit dsPIC33F CPU
⢠Code-Efficient (C and Assembly) Architecture
⢠Two 40-Bit Wide Accumulators
⢠Single-Cycle (MAC/MPY) with Dual Data Fetch
⢠Single-Cycle Mixed-Sign MUL plus Hardware Divide
⢠32-Bit Multiply Support
Clock Management
⢠±0.25% Internal Oscillator
⢠Programmable PLLs and Oscillator Clock Sources
⢠Fail-Safe Clock Monitor (FSCM)
⢠Independent Watchdog Timer (WDT)
⢠Fast Wake-up and Start-up
Power Management
⢠Low-Power Management modes (Sleep, Idle, Doze)
⢠Integrated Power-on Reset and Brown-out Reset
⢠1 mA/MHz Dynamic Current (typical)
⢠30 µA IPD Current (typical)
PWM
⢠Up to Three PWM Pairs
⢠Two Dead-Time Generators
⢠31.25 ns PWM Resolution
⢠PWM Support for:
- Inverters, PFC, UPS
- BLDC, PMSM, ACIM, SRM
⢠Class B-Compliant Fault Inputs
⢠Possibility of ADC Synchronization with PWM Signal
Advanced Analog Features
⢠ADC module:
- 10-bit, 1.1 Msps with four S&H
- Four analog inputs on 18-pin devices and up to
14 analog inputs on 44-pin devices
⢠Flexible and Independent ADC Trigger Sources
⢠Three Comparator modules
⢠Charge Time Measurement Unit (CTMU):
- Supports mTouch⢠capacitive touch sensing
- Provides high-resolution time measurement (1 ns)
- On-chip temperature measurement
Timers/Output Compare/Input Capture
⢠Up to Five General Purpose Timers:
- One 16-bit and up to two 32-bit timers/counters
⢠Two Output Compare modules
⢠Three Input Capture modules
⢠Peripheral Pin Select (PPS) to allow Function Remap
Communication Interfaces
⢠UART module (4 Mbps)
- With support for LIN/J2602 Protocols and IrDA®
⢠4-Wire SPI module (8 MHz maximum speed)
- Remappable Pins in 32-Kbyte Flash Devices
⢠I2C⢠module (400 kHz)
Input/Output
⢠Sink/Source 10 mA or 6 mA, Pin-Specific for Standard
VOH/VOL, up to 16 mA or 12 mA for Non-Standard VOH1
⢠5V Tolerant Pins
⢠Up to 20 Selectable Open-Drain and Pull-ups
⢠Three External Interrupts (two are remappable)
Qualification and Class B Support
⢠AEC-Q100 REVG (Grade 1 -40ºC to +125ºC) Planned
⢠Class B Safety Library, IEC 60730, UDE Certified
Debugger Development Support
⢠In-Circuit and In-Application Programming
⢠Up to Three Complex Data Breakpoints
⢠Trace and Run-Time Watch
ï£ 2011-2012 Microchip Technology Inc.
DS70652E-page 1
|
▷ |