|
DSPIC33FJ06GS101A-I Datasheet, PDF (1/352 Pages) Microchip Technology – 16-Bit Microcontrollers and Digital Signal Controllers with High-Speed PWM, ADC and Comparators | |||
|
dsPIC33FJ06GS001/101A/102A/202A
and dsPIC33FJ09GS302
16-Bit Microcontrollers and Digital Signal Controllers with
High-Speed PWM, ADC and Comparators
Operating Conditions
⢠3.0V to 3.6V, -40ºC to +125ºC, DC to 40 MIPS
Core: 16-Bit dsPIC33F CPU
⢠Code Efficient (C and Assembly) Architecture
⢠Two 40-Bit Wide Accumulators
⢠Single-Cycle (MAC/MPY) with Dual Data Fetch
⢠Single-Cycle Mixed-Sign MUL plus Hardware Divide
⢠32-Bit Multiply Support
Clock Management
⢠±2% Internal Oscillator
⢠Programmable PLLs and Oscillator Clock Sources
⢠Fail-Safe Clock Monitor (FSCM)
⢠Independent Watchdog Timer (WDT)
⢠Fast Wake-up and Start-up
Power Management
⢠Low-Power Management modes (Sleep, Idle, Doze)
⢠Integrated Power-on Reset and Brown-out Reset
⢠2.0 mA/MHz Dynamic Current (typical)
⢠135 µA IPD Current (typical)
High-Speed PWM
⢠Up to Three PWM Pairs with Independent Timing
⢠Dead Time for Rising and Falling Edges
⢠1.04 ns PWM Resolution for Dead Time, Duty Cycle,
Phase and Frequency
⢠PWM Support for:
- DC/DC, AC/DC, Inverters, PFC and Lighting
⢠Programmable Fault Inputs
⢠Flexible Trigger Configurations for ADC Conversions
Advanced Analog Features
⢠Two High-Speed Comparators with Direct Connection to
the PWM module:
- Buffered/amplified output drive
- Independent 10-bit DAC for each comparator
- Rail-to-rail comparator operation
- DACOUT amplifier (1x, 1.8x)
- Selectable hysteresis
- Programmable output polarity
- Interrupt generation capability
Advanced Analog Features (Continued)
⢠ADC module:
- 10-bit resolution with Successive Approximation
Register (SAR) converter (2 Msps) and three
Sample-and-Hold (S&H) circuits
- Up to 8 input channels grouped into four conversion
pairs, plus two inputs for monitoring voltage references
- Flexible and independent ADC trigger sources
- Dedicated Result register for each
analog channel
Timers/Output Compare/Input Capture
⢠Two 16-Bit General Purpose Timers/Counters
⢠Input Capture module
⢠Output Compare module
⢠Peripheral Pin Select (PPS) to allow Function Remap
Communication Interfaces
⢠UART module (10 Mbps):
- With support for LIN/J2602 protocols and IrDA®
⢠4-Wire SPI module
⢠I2C⢠module (up to 1 Mbaud) with SMBus Support
⢠PPS to allow Function Remap
Input/Output
⢠Constant Current Source:
- Constant current generator (10 µA nominal)
⢠Sink/Source 18 mA on 8 Pins and 6 mA on 13 Pins
⢠5V Tolerant Pins
⢠Selectable Open-Drain and Pull-ups
⢠External Interrupts on 16 I/O Pins
Qualification and Class B Support
⢠AEC-Q100 REVG (Grade 1, -40ºC to +125ºC) Planned
⢠Class B Safety Library, IEC 60730
Debugger Development Support
⢠In-Circuit and In-Application Programming
⢠Two Breakpoints
⢠IEEE 1149.2 Compatible (JTAG) Boundary Scan
⢠Trace and Run-Time Watch
ï£ 2011-2012 Microchip Technology Inc.
DS75018C-page 1
|
▷ |