MAX1242 Datasheet, PDF (7/12 Pages) Maxim Integrated Products – +2.7V to %.25V, Low-Power, 10-Bit Serial ADCs in SO-8

+2.7V to +5.25V, Low-Power, 10-Bit
Serial ADCs in SO-8
+2.7V to +5.25V
4.7µF 0.1µF
1 _VDD
SCLK ⁸
ANALOG INPUT
0V TO V_REF
2 _AIN
CS ⁷
SHUTDOWN
INPUT
REFERENCE
INPUT
MAX1243
MAX1242
MAX1243
3 _SHDN
DOUT ⁶
4 _REF
GND ⁵
C*
*4.7µF, MAX1242
0.1µF, MAX1243
Figure 3. Operational Diagram
SERIAL
INTERFACE
where R_IN = 9kΩ, R_S = the input signal’s source imped-
ance, and t_ACQ is never less than 1.5µs. Source imped-
ances below 4kΩ do not significantly affect the ADC’s
AC performance.
Higher source impedances can be used if a 0.01µF
capacitor is connected to the analog input. Note that
the input capacitor forms an RC filter with the input
source impedance, limiting the ADC’s input signal
bandwidth.
Input Bandwidth
The ADC’s input tracking circuitry has a 2.25MHz
small-signal bandwidth, so it is possible to digitize
high-speed transient events and measure periodic sig-
nals with bandwidths exceeding the ADC’s sampling
rate by using undersampling techniques. To avoid
aliasing of unwanted high-frequency signals into the
frequency band of interest, anti-alias filtering is recom-
mended.
Analog Input Protection
Internal protection diodes, which clamp the analog
input to V_DD and GND, allow the input to swing from
GND - 0.3V to V_DD + 0.3V without damage. However,
for accurate conversions near full scale, the input must
not exceed V_DD by more than 50mV, or be lower than
GND by 50mV.
If the analog input exceeds 50mV beyond the supplies,
limit the input current to 2mA.
CAPACITIVE DAC
REF
AIN ^TRACK _INPUT ^CHOLD
COMPARATOR
ZERO
-+
HOLD
16pF
9k
C_SWITCH
R_IN
HOLD
TRACK
AT THE SAMPLING INSTANT,
THE INPUT SWITCHES FROM
AIN TO GND.
GND
Figure 4. Equivalent Input Circuit
Internal Reference (MAX1242)
The MAX1242 has an on-chip voltage reference
trimmed to 2.5V. The internal reference output is con-
nected to REF and also drives the internal capacitive
DAC. The output can be used as a reference voltage
source for other components and can source up to
400µA. Bypass REF with a 4.7µF capacitor. Larger
capacitors increase wake-up time when exiting shut-
down (see Using SHDN to Reduce Supply Current).
The internal reference is enabled by pulling the SHDN
pin high. Letting SHDN float disables the internal refer-
ence, which allows the use of an external reference, as
described in the External Reference section.
External Reference
The MAX1242/MAX1243 operate with an external refer-
ence at the REF pin. To use the MAX1242 with an
external reference, disable the internal reference by let-
ting SHDN float. Stay within the voltage range 1.0V to
V_DD to achieve specified accuracy. The minimum input
impedance is 18kΩ for DC currents. During conver-
sion, the external reference must be able to deliver up
to 250µA of DC load current and have an output
impedance of 10Ω or less. The recommended mini-
mum value for the bypass capacitor is 0.1µF. If the ref-
erence has higher output impedance or is noisy,
bypass it close to the REF pin with a 4.7µF capacitor.
_______________________________________________________________________________________ 7