MAX1184 Datasheet, PDF (5/21 Pages) Maxim Integrated Products – Dual 10-Bit, 20Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs

Dual 10-Bit, 20Msps, +3V, Low-Power ADC with
Internal Reference and Parallel Outputs
ELECTRICAL CHARACTERISTICS (continued)
(V_DD = +3V, OV_DD = +2.5V, 0.1µF and 1.0µF capacitors from REFP, REFN, and COM to GND; REFOUT connected to REFIN through
a 10kΩ resistor, V_IN = 2Vp-p (differential w.r.t. COM), C_L = 10pF at digital outputs (Note 5), f_CLK = 20MHz, T_A = T_MIN to T_MAX, unless
otherwise noted. Typical values are at T_A = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX UNITS
POWER REQUIREMENTS
Analog Supply Voltage Range
Output Supply Voltage Range
Analog Supply Current
V_DD
OV_DD
I_VDD
Operating, f_{INA or B} = 7.5MHz at -0.5dB FS
Sleep mode
Shutdown, clock idle, PD = OE = OV_DD
2.7
3.0
3.6
V
1.7
2.5
3.6
V
35
50
mA
2.8
1
15
µA
Output Supply Current
Power Dissipation
Power-Supply Rejection Ratio
TIMING CHARACTERISTICS
CLK Rise to Output Data Valid
Output Enable Time
Output Disable Time
CLK Pulse Width High
CLK Pulse Width Low
Wake-Up Time
I_OVDD
PDISS
PSRR
Operating, C_L = 15pF, f_{INA or B} = 7.5MHz at
-0.5dB FS
Sleep mode
Shutdown, clock idle, PD = OE = OV_DD
Operating, f_{INA or B} = 7.5MHz at -0.5dB FS
Sleep mode
Shutdown, clock idle, PD = OE = OV_DD
Offset
Gain
t_DO
t_ENABLE
t_DISABLE
t_CH
t_CL
t_WAKE
Figure 3 (Note 3)
Figure 4
Figure 4
Figure 3, clock period: 50ns
Figure 3, clock period: 50ns
Wakeup from sleep mode (Note 4)
Wakeup from shutdown (Note 4)
3.8
mA
100
µA
2
10
105 150
mW
8.4
3
45
µW
±0.2
mV/V
±0.1
%/V
5
8
ns
10
ns
1.5
ns
25 ± 7.5
ns
25 ± 7.5
ns
0.51
µs
1.5
CHANNEL-TO-CHANNEL MATCHING
Crosstalk
Gain Matching
Phase Matching
f_{INA or B} = 7.5MHz at -0.5dB FS
f_{INA or B} = 7.5MHz at -0.5dB FS
f_{INA or B} = 7.5MHz at -0.5dB FS
-70
dB
0.02 ±0.2
dB
0.25
d eg r ees
Note 1: SNR, SINAD, THD, SFDR, and HD3 are based on an analog input voltage of -0.5dB FS referenced to a +1.024V full-scale
input voltage range.
Note 2: Intermodulation distortion is the total power of the intermodulation products relative to the individual carrier. This number is
6dB or better, if referenced to the two-tone envelope.
Note 3: Digital outputs settle to V_IH, V_IL. Parameter guaranteed by design.
Note 4: With REFIN driven externally, REFP, COM, and REFN are left floating while powered down.
Note 5: Equivalent dynamic performance is obtainable over full OV_DD range with reduced C_L.
_______________________________________________________________________________________ 5