MAX1428 Datasheet, PDF (16/18 Pages) Maxim Integrated Products – 15-Bit, 80Msps ADC with -78.4dBFS Noise Floor for IF Applications

15-Bit, 80Msps ADC with -78.4dBFS
Noise Floor for IF Applications
Differential Nonlinearly (DNL)
Differential nonlinearity is the difference between an
actual step width and the ideal value of 1 LSB. A DNL
error specification of less than 1 LSB guarantees no
missing codes and a monotonic transfer function. The
MAX1428’s DNL specification is measured with the his-
togram method based on a 15MHz input tone.
Dynamic Parameter Definitions
Aperture Delay
Aperture delay (t_AD) is the time defined between the
rising edge of the sampling clock and the instant when
an actual sample is taken (Figure 4).
Aperture Jitter
The aperture jitter (t_AJ) is the sample-to-sample varia-
tion in the aperture delay.
Signal-to-Noise Ratio (SNR)
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
the full-scale analog input (RMS value) to the RMS
quantization error (residual error). The ideal, theoretical
minimum analog-to-digital noise is caused by quantiza-
tion error only and results directly from the ADC’s reso-
lution (N bits):
SNR_dB[max] = 6.02_dB x N + 1.76_dB
In reality, other noise sources such as thermal noise,
clock jitter, signal phase noise, and transfer function
nonlinearities are also contributing to the SNR calcula-
tion and should be considered when determining the
SNR in ADC. For a near-full-scale analog input signal
(-0.5dBFS to -1dBFS), thermal and quantization noise
are uniformly distributed across the frequency bins.
Error energy caused by transfer function nonlinearities
on the other hand is not distributed uniformly, but con-
fined to the first few hundred odd-order harmonics.
BTS applications, which are the main target application
for the MAX1428 usually do not care about excess
noise and error energy in close proximity to the carrier
frequency or to DC. These low-frequency and sideband
errors are test system artifacts and are of no conse-
quence to the BTS channel sensitivity. They are there-
fore excluded from the SNR calculation.
Signal-to-Noise Plus Distortion (SINAD)
SINAD is computed by taking the ratio of the RMS sig-
nal to all spectral components excluding the fundamen-
tal and the DC offset.
Single-Tone Spurious-Free
Dynamic Range (SFDR)
SFDR is the ratio of RMS amplitude of the carrier fre-
quency (maximum signal component) to the RMS value
of the next-largest noise or harmonic distortion compo-
nent. SFDR is usually measured in dBc with respect to
the carrier frequency amplitude or in dBFS with respect
to the ADC’s full-scale range.
Two-Tone Spurious-Free
Dynamic Range (SFDR_TT)
SFDR_TT represents the ratio of the RMS value of either
input tone to the RMS value of the peak spurious com-
ponent in the power spectrum. This peak spur can be
an intermodulation product of the two input test tones.
Two-Tone Intermodulation Distortion (IMD)
The two-tone IMD is the ratio expressed in decibels of
either input tone to the worst 3rd-order (or higher) inter-
modulation products. The individual input tone levels
are at -8dB full scale.
Pin Configuration
TOP VIEW
56 55 54 53 52 51 50 49 48 47 46 45 44 43
GND 1
EP
GND 2
GND 3
42 DRVCC
41 DRVCC
40 D7
CLKP 4
39 D6
CLKN 5
38 D5
GND 6
37 D4
AVCC 7
AVCC 8
GND 9
MAX1428
36 D3
35 D2
34 D1
INP 10
33 D0
INN 11
32 DOR
GND 12
CM 13
31 DRVCC
30 GND
GND 14
29 DVCC
15 16 17 18 19 20 21 22 23 24 25 26 27 28
THIN QFN
16 ______________________________________________________________________________________