|
108-5246 Datasheet, PDF (8/21 Pages) Tyco Electronics – This specification covers the requirements for product performance | |||
|
◁ |
Product Specification
108-5246
é
ç®
Para.
3.5.17
試é¨é
ç®
Test Items
å¾®å æ¯å
(ãã³ãã¼è¡æ)
3.5.17 Hammerring Shocks
3.5.18 è¡æ
è¦æ ¼å¤
Requirements
å æ¯ä¸ 1μsecããããä¸é£ç¶
å°éãçããªããã¨ã
ç·åæµæï¼ãã¼ã¬ãã«ï¼ï¼
20 mΩ æ大(試é¨å¾)
試é¨æ¹æ³
Procedures
åµåããã³ãã¯ã¿ãFig.8ã«ç¤ºã
æ¡ä»¶ã§10000åå æ¯ããFig.9ã«ç¤º
ã測å®åè·¯ã«ããå°å é»å§ DC
10V,1mAã®è©¦é¨é»æµãéé»ããã
ç¶æ
ã§è©¦é¨ãè¡ããå æ¯ä¸ã®æµæ
ã®å¤åãã¢ãã¿ã¼ããã
å°ãåµåå¾ã®ã³ãã¯ã¿ã¯Fig.7ã«
示ãæ§ã«åºå®ãã¦è¡ãã
No electrical discontinuity
greater than 1μsec.shall
occur.
Termination resistance
(low level)(Final)
20 mΩ Max.
Subject mated connectors on PCB
as shown in Fig.7,Under 10000
cycles of repeated hammering
shocks of the condition as
shown in Fig.8,with the test
current of 1mA at 10VDC applied
to the circuit as shown in
Fig.9.During the test, the
circuit shall be monitored for
fluctuation of electrical
resistance.
The clamping manner shall be in
accordance with Fig.7 after
mating the connectors.
è¡æã«ãã1 μsec. ãè¶ãã
ä¸é£ç¶å°éãçããªããã¨ã
ç·åæµæï¼ãã¼ã¬ãã«ï¼ï¼
20 mΩ æ大(試é¨å¾)
åµåããã³ãã¯ã¿ã«11mç§éã«
50Gã®æ£å¼¦æ³¢ãçãããããªè¡æ
ãç´äº¤ããä¸æ¹å軸ã®æ£è² æ¹å
ã«ï¼åã¾ã§åè¨18åä¸ãããã¨
MIL-STD-202ãé¨æ³213,æ¡ä»¶A
å°ãåµåå¾ã®ã³ãã¯ã¿ã¯Fig.7ã«
示ãæ§ã«åºå®ãã¦è¡ãã
Fig.2 ï¼ç¶ãï¼
Fig.2(To be continued)
Rev. L
8 of 21
|
▷ |