LTC3209-1 Datasheet, PDF (16/20 Pages) Linear Technology – 600mA Main/Camera LED Controller

LTC3209-1/LTC3209-2
APPLICATIO S I FOR ATIO
V_BAT, CPO Capacitor Selection
The style and value of the capacitors used with the
LTC3209-1/LTC3209-2 determine several important
parameters such as regulator control loop stability, output
ripple, charge pump strength and minimum start-up time.
To reduce noise and ripple, it is recommended that low
equivalent series resistance (ESR) ceramic capacitors are
used for both CV_BAT and C_CPO. Tantalum and aluminum
capacitors are not recommended due to high ESR.
The value of C_CPO directly controls the amount of output
ripple for a given load current. Increasing the size of C_CPO
will reduce output ripple at the expense of higher start-up
current. The peak-to-peak output ripple of the 1.5x mode
is approximately given by the expression:
V_RIPPLE(P-P)
=
I_OUT
3f_OSC • C_CPO
Where f_OSC is the LTC3209-1/LTC3209-2 oscillator
frequency or typically 850kHz and C_CPO is the output
storage capacitor.
The output ripple in 2x mode is very small due to the fact
that load current is supplied on both cycles of the clock.
Both style and value of the output capacitor can signifi-
cantly affect the stability of the LTC3209-1/LTC3209-2. As
shown in the Block Diagram, the LTC3209-1/LTC3209-2
use a control loop to adjust the strength of the charge
pump to match the required output current. The error
signal of the loop is stored directly on the output capacitor.
The output capacitor also serves as the dominant pole for
the control loop. To prevent ringing or instability, it is
important for the output capacitor to maintain at least 1µF
of capacitance over all conditions.
In addition, excessive output capacitor ESR will tend to
degrade the loop stability. If the output capacitor has
160mΩ or more of ESR, the closed-loop frequency
response will cease to roll off in a simple one-pole fashion
and poor load transient response or instability may
occur. Multilayer ceramic chip capacitors typically have
exceptional ESR performance. MLCCs combined with a
tight board layout will result in very good stability. As the
16
value of C_CPO controls the amount of output ripple, the
value of CV_BAT controls the amount of ripple present at
the input pin (V_BAT). The LTC3209-1/LTC3209-2 input
current will be relatively constant while the charge pump
is either in the input charging phase or the output
charging phase but will drop to zero during the clock
nonoverlap times. Since the nonoverlap time is small
(~25ns), these missing “notches” will result in only a
small perturbation on the input power supply line. Note
that a higher ESR capacitor such as tantalum will have
higher input noise due to the higher ESR. Therefore,
ceramic capacitors are recommended for low ESR. Input
noise can be further reduced by powering the LTC3209-
1/LTC3209-2 through a very small series inductor as
shown in Figure 6. A 10nH inductor will reject the fast
current notches, thereby presenting a nearly constant
current load to the input power supply. For economy, the
10nH inductor can be fabricated on the PC board with
about 1cm (0.4") of PC board trace.
VBAT
LTC3209-1
LTC3209-2
GND
320912 F06
Figure 6. 10nH Inductor Used for Input Noise Reduction
(Approximately 1cm of Board Trace)
Flying Capacitor Selection
Warning: Polarized capacitors such as tantalum or
aluminum should never be used for the flying capacitors
since their voltage can reverse upon start-up of the
LTC3209-1/LTC3209-2. Ceramic capacitors should
always be used for the flying capacitors.
The flying capacitors control the strength of the charge
pump. In order to achieve the rated output current it is
necessary to have at least 1.6µF of capacitance for each of
the flying capacitors. Capacitors of different materials lose
their capacitance with higher temperature and voltage at
different rates. For example, a ceramic capacitor made of
X7R material will retain most of its capacitance from
–40°C to 85°C whereas a Z5U or Y5V style capacitor will
320912fa