Z-SERIES Datasheet, PDF (31/41 Pages) Keysight Technologies – Infiniium Z-Series Oscilloscopes

31 | Keysight | Infiniium Z-Series Oscilloscopes - Data Sheet
Specifications
Vertical
Typical analog bandwidth (3 dB)
Analog bandwidth (3 dB) *
1-channel sample rate
2-channel sample rate
4-channel sample rate
Rise time/fall time
10 to 90% ⁴
20 to 80% ⁵
Input impedance ³
Sensitivity ²
Input coupling
Vertical resolution ¹
Channel to channel isolation (any two channels
with equal V/div settings)
DC gain accuracy *
Maximum input voltage
Offset range
Offset accuracy *
Dynamic range
DC voltage measurement accuracy
RMS noise floor (scope only)
Volts/div
10 mV
50 mV
100 mV
1V
Z204A Z254A Z334A Z504A Z592A Z594A Z632A Z634A
20 GHz 25 GHz 33 GHz 50 GHz 59 GHz 59 GHz 63 GHz 63 GHz
20 GHz 25 GHz 32 GHz 50 GHz 59 GHz 59 GHz 62 GHz 62 GHz
80
80
80
160
160
160
160
160
80
80
80
160
80
160
80
160
80
80
80
80
—
80
—
80
Z204A Z254A Z334A Z504A Z592A Z594A Z632A Z634A
22.0 ps 17.6 ps 13.3 ps 8.8 ps
7.5 ps
7.5 ps
7.0 ps
7.0 ps
15.6 ps 12.4 ps 9.4 ps
6.2 ps
5.3 ps
5.3 ps
4.9 ps
4.9 ps
50 Ω, ± 3%
1 mV/div to 1 V/div
DC
8 bits, ≥ 12 bits with averaging
Replace existing channel to channel isolation specs with the following:
RealEdge (1.85 mm) channels
DC to 40 GHz: 70 dB
40 GHz to BW: 60 dB
Standard (3.5 mm) channels
DC to BW: 70 dB
± 2% of full scale at full resolution channel scale (± 2.5% for 5 mV/div)
± 5 V for steady state and transient measurements
Vertical sensitivity
Available offset
Available offset (oscilloscope with
N7010A voltage termination adapter)
1 to 49 mV/div
± 0.4 V
±4V
50 to 79 mV/div
± 0.7 V
±4V
80 to 134 mV/div
± 1.2 V
±4V
135 to 239 mV/div
± 2.2 V
±4V
240 mV/div to 1 V/div
± 4.0 V
±4V
≤ 3.5 V: ± (2% of channel offset + 1% of full scale) + 1 mV
> 3.5 V: ± (2% of channel offset + 1% of full scale)
± 4 div from center screen
Dual cursor: ± [(DC gain accuracy) + (resolution)]
Single cursor: ± [(DC gain accuracy) + (offset accuracy) + (resolution/2)]
Z204A
Z254A
Z334A
Z504A
Z594A, Z592A Z634A, Z632A
0.41 mV (rms)
1.46 mV (rms)
2.90 mV (rms)
28.6 mV (rms)
0.48 mV (rms)
1.7 mV (rms)
3.3 mV (rms)
32.5 mV (rms)
0.60 mV (rms)
2.00 mV (rms)
3.90 mV (rms)
38.1 mV (rms)
0.90 mV (rms)
2.90 mV (rms)
5.70 mV (rms)
56.7 mV (rms)
0.96 mV (rms)
3.15 mV (rms)
6.2 mV (rms)
60 mV (rms)
1.0 mV (rms)
3.3 mV (rms)
6.4 mV (rms)
63 mV (rms)
* Denotes warranted specifications, all others are typical. Specifications are valid after a 30-minute warm up period, and ± 5 °C from annual calibration
temperature.
1.  Vertical resolution for 8 bits = 0.4% of full scale, for 12 bits = 0.024% of full scale.
2.  Full scale is defined as 8 vertical divisions. Magnification is used below 7.5 mV/div. Below 7.5 mV/div, full-scale is defined as 60 mV/div. The major scale
settings are 5 mV, 10 mV, 20 mV, 50 mV, 100 mV, 200 mV, 500 mV, and 1 V.
3.  Input impedance is valid when V/div scaling is adjusted to show all waveform vertical values within scope display.
4.  Rise time calculated by using 0.44/BW for (10 to 90%) rise time.
5.  Rise time calculated by using 0.31/BW for (20 to 80%) rise time.