ISL75051SRH Datasheet, PDF (5/15 Pages) Intersil Corporation – 3A, Rad Hard, Positive, Ultra Low Dropout Regulator

ISL75051SRH
Absolute Maximum Ratings
V_IN Relative to GND (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +6.7V
V_OUT Relative to GND (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +6.7V
PG, EN, OCP/ADJ Relative to GND (Note 3). . . . . . . . . . . . . -0.3 to +6.7VDC
Junction Temperature (T_J) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +175°C
Recommended Operating Conditions (Note 4)
Ambient Temperature Range (T_A) . . . . . . . . . . . . . . . . . . .-55°C to +125°C
Junction Temperature (T_J) (Note 3). . . . . . . . . . . . . . . . . . . . . . . . . . .+150°C
V_IN Relative to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2V to 6.0V
V_OUT Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.8V to 5.0V
PG, EN, OCP/ADJ relative to GND . . . . . . . . . . . . . . . . . . . . . . . 0V to +6.0V
Thermal Information
Thermal Resistance (Typical)
θ_JA (°C/W) θ_JC (°C/W)
18 Ld CDFP Package (Notes 5, 6) . . . . . . .
28
4
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Radiation Information
Max Total Dose
(Dose Rate = 50 - 300radSi/s . . . . . . . . . . . . . . . . . . . . . . . 100 krad (Si)
SET (V_OUT < ±5% During Events (Note 7). . . . . . . . . . . . . . 86MeV^•cm²/mg
SEL/B (No Latchup/Burnout . . . . . . . . . . . . . . . . . . . . . . . . 86MeV^•cm²/mg
The output capacitance used for SEE testing is 220µF for C_IN and C_OUT,
200nF for BYPASS
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
3. Extended operation at these conditions may compromise reliability. Exceeding these limits will result in damage. Recommended operating conditions
define limits where specifications are guaranteed.
4. Refer to “Thermal Guidelines” on page 12.
5. θ_JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379
6. For θ_JC, the “case temp” location is the center of the package underside.
7. The device can work down to V_OUT = 0.8V; however, the SET performance of < ±5% at LET = 86MeV.cm²/mg is guaranteed at V_OUT = >1.5V only. SET
tests performed with 220µF 10V 25mΩ and 0.1µF CDR04 capacitor on the input and output.
Electrical Specifications Unless otherwise noted, all parameters are guaranteed over the following specified conditions:
V_IN = V_OUT + 0.4V, V_OUT = 1.8V, C_IN = C_OUT = 220µF 25mΩ and 0.1µF X7R, T_J = +25°C, I_L = 0A. Applications must follow thermal guidelines of
the package to determine worst-case junction temperature. Please refer to “Applications Information” on page 11 of the datasheet and
Tech Brief TB379. Boldface limits apply over the operating temperature range, -55°C to +125°C. Pulse load techniques used by ATE to ensure
T_J = T_A defines guaranteed limits.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
MAX
(Note 8)
TYP
(Note 8) UNITS
DC CHARACTERISTICS
DC Output Voltage Accuracy
Feedback Pin
BYP Pin
DC Input Line Regulation
V_OUT
V_OUT Resistor adjust to 0.52V, 1.5V and 1.8V
2.2V < V_IN < 3.6V; 0A < I_LOAD < 3.0A
-1.5
0.2
1.5
%
V_OUT Resistor adjust to 5.0V
V_OUT + 0.4V < V_IN < 6.0V; 0A < I_LOAD < 3.0A
-1.5
0.2
1.5
%
V_ADJ
2.2V < V_IN < 6.0V; I_LOAD = 0A
514.8
520
525.2
mV
V_BYP
2.2V < V_IN < 6.0V; I_LOAD = 0A
520
mV
2.2V < V_IN < 3.6V, V_OUT = 1.5V, +25°C & -55°C
(Note 9)
1.13
3.5
mV
DC Input Line Regulation
DC Input Line Regulation
2.2V < V_IN < 3.6V, V_OUT = 1.5V, +125°C (Note 9)
2.2V < V_IN < 3.6V, V_OUT = 1.8V, +25°C & -55°C
(Note 9)
1.13
8.0
mV
1.62
3.5
mV
DC Input Line Regulation
DC Input Line Regulation
DC Output Load Regulation
2.2V < V_IN < 3.6V, V_OUT = 1.8V, +125°C (Note 9)
1.62
10.5
mV
V_OUT + 0.4V < V_IN < 6.0V, V_OUT = 5.0V (Note 9)
12.50
20.0
mV
V_OUT = 1.5V; 0A < I_LOAD < 3.0A, V_IN = V_OUT + 0.4V
-4.0
-0.8
-0.1
mV
(Note 9)
DC Output Load Regulation
V_OUT = 1.8V; 0A < I_LOAD < 3.0A, V_IN = V_OUT + 0.4V
-4.0
(Note 9)
-1.2
-0.05
mV
DC Output Load Regulation
V_OUT = 5.0V; 0A < I_LOAD < 3.0A, V_IN = V_OUT + 0.4V
-15.0
-6.0
-0.05
mV
(Note 9)
5
FN7610.1
November 4, 2011