ISL71090SEH50 Datasheet, PDF (5/13 Pages) Intersil Corporation – RH voltage regulators precision outputs

ISL71090SEH50
Absolute Maximum Ratings
Maximum Voltage
V_IN to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +40V
V_IN to GND at an LET = 86MeV•cm²/mg . . . . . . . . . . . . . . -0.5V to +36V
V_OUT to GND (10s). . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.5V to V_OUT + 0.5V
Voltage on any Pin to Ground . . . . . . . . . . . . . . . . . -0.5V to +V_OUT + 0.5V
Voltage on DNC Pins . . . . . . . . . . . . No connections permitted to these pins
ESD Ratings
Human Body Model (Tested per MIL-PRF-883 3015.7). . . . . . . . . . . 2kV
Machine Model (Tested per JESD22-A115-A) . . . . . . . . . . . . . . . . . . 200V
Charged Device Model (Tested per JESD22-C101D)). . . . . . . . . . . 750V
Thermal Information
Thermal Resistance (Typical)
_JA (°C/W) _JC (°C/W)
8 Ld Flatpack Package (Notes 3, 4). . . . . . 140
15
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Maximum Junction Temperature (T_JMAX). . . . . . . . . . . . . . . . . . . . . .+150°C
Recommended Operating Conditions
V_IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0V to +30V
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55°C to +125°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
3. _JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
4. For _JC, the “case temp” location is the center of the ceramic on the package underside.
5. Product capability established by initial characterization. The “EH” version is acceptance tested on a wafer-by-wafer basis to 50krad(Si) at low dose rate.
6. The output capacitance used for SEE testing is C_IN = 0.1µF and C_OUT = 1µF.
Electrical Specifications for Flatpack V_IN = 10V, I_OUT = 0mA, C_L = 0.1µF and C_C = 1nF unless otherwise specified. Boldface
limits apply after radiation at +25°C and across the operating temperature range, -55°C to +125°C without radiation, unless otherwise specified.
PARAMETER
DESCRIPTION
TEST CONDITIONS
MIN
MAX
(Note 7)
TYP
(Note 7)
UNIT
V_OUT
Output Voltage
V_OA
V_OUT Accuracy at T_A = +25°C
V_OUT = 5.005V, (Note 10)
V_OUT Accuracy at T_A = -55°C to +125°C V_OUT = 5.005V, (Note 10)
V_OUT Accuracy at T_A = +25°C, Post
Radiation
V_OUT = 5.005V, (Note 10)
5.005
V
-0.05
+0.05
%
-0.15
+0.15
%
-0.3
+0.3
%
TC V_OUT
Output Voltage Temperature
Coefficient (Note 8)
10
ppm/°C
V_IN
I_IN
V_OUT /V_IN
V_OUT/I_OUT
Input Voltage Range
Supply Current
Line Regulation
Load Regulation
V_D
Dropout Voltage
(Note 9)
V_IN = 7.0V to 30V
Sourcing: 0mA ≤ I_OUT ≤ 20mA
Sinking: -10mA ≤ I_OUT ≤ 0mA
I_OUT = 10mA
7.0
30
V
0.930
1.500
mA
8
20
ppm/V
10
20
ppm/mA
21
40
ppm/mA
1.5
1.7
V
I_SC+
I_SC-
t_R
PSRR
Short-Circuit Current
Short-Circuit Current
Turn-On Settling Time
Ripple Rejection
T_A = +25°C, V_OUT tied to GND
T_A = +25°C, V_OUT tied to V_IN
90% of final value, C_L = 1.0µF,
C_C = open
f = 120Hz
53
mA
-63
mA
250
µs
90
dB
e_N
V_N
V_OUT/t
Output Voltage Noise
Broadband Voltage Noise
Noise Density
Long Term Drift
0.1Hz ≤ f ≤10Hz
10Hz ≤ f ≤1kHz
f = 1kHz, V_IN = 7.1V
T_A = 125°C, 1000hrs
1.1
µV_P-P
2.2
µV_RMS
68
nV/√Hz
15
ppm
Submit Document Feedback
5
FN8588.3
March 15, 2016