ISL6569A Datasheet, PDF (5/22 Pages) Intersil Corporation – Multi-Phase PWM Controller

ISL6569A
Absolute Maximum Ratings
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7V
Input, Output, or I/O Voltage . . . . . . . . . . . GND -0.3V to V_CC + 0.3V
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 3kV
Operating Conditions
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V ±5%
Ambient Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 0^oC to 70^oC
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . 0^oC to 125^oC
Thermal Information
Thermal Resistance (Typical, Note 1)
θ_JA (^oC/W) θ_JC (^oC/W)
SOIC Package (Note 1) . . . . . . . . . . . .
63
N/A
QFN Package (Notes 2, 3) . . . . . . . . . .
32
4
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . .150^oC
Maximum Storage Temperature Range . . . . . . . . . . -65^oC to 150^oC
Maximum Lead Temperature . . . . . . . . . . . . . . . . . . . . . . . . . .300^oC
(SOIC - Lead Tips Only)
CAUTION: Stress above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device
at these or any other conditions above those indicated in the operational section of this specification is not implied.
NOTES:
1. θ_JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
2. θ_JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
3. For θ_JC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications Operating Conditions: VCC = 5V, T_A = 0^o C to 70^oC. Unless Otherwise Specified.
PARAMETER
TEST CONDITIONS
MIN
TYP MAX UNITS
VCC SUPPLY CURRENT
Nominal Supply
Shutdown Supply
SHUNT REGULATOR
VCC = 5VDC; EN = 5VDC; R_T = 100 kΩ ±1%
VCC = 5VDC; EN = 0VDC; R_T = 100 kΩ ±1%
8.0 10.8 14.0 mA
8.0 10.3 13.0 mA
VCC Voltage
VCC Sink Current
POWER-ON RESET AND ENABLE
VCC tied to 12VDC thru 300Ω resistor, R_T = 100kΩ
VCC tied to 12VDC thru 300Ω resistor, R_T = 100kΩ
5.63 5.8 5.97 V
15 20 25 mA
POR Threshold
VCC Rising
4.25 4.35 4.50 V
VCC Falling
3.75 3.85 4.00 V
ENABLE Threshold
EN Rising
1.205 1.23 1.255 V
Hysteresis
86 92 98 mV
REFERENCE VOLTAGE AND DAC
Reference Voltage
0.792 0.8 0.808 V
System Accuracy
(Note 4)
-0.5
-
0.5 %VID
VID on Fly Step Size
VID Pull Up
R_T = 100kΩ
-
25
-
mV
-
-20
-
µA
VID Input Low Level
-
0.8
V
VID Input High Level
- 1.36 1.6
V
PIN-ADJUSTABLE OFFSET
OFS Current
- 100 -
µA
Offset Accuracy
ROFS = 5.00kΩ ±1%
47.0 50.0 53.0 mV
OSCILLATOR
Accuracy
-10
-
10
%
Adjustment Range
0.08 -
1.0 MHz
5
FN9092.2
December 29, 2004