ISL43640_14 Datasheet, PDF (5/13 Pages) Intersil Corporation – Low-Voltage, Single Supply, 4 to 1 Multiplexer, High Performance Analog Switch

ISL43640
Electrical Specifications +3V Supply
Test Conditions: V+ = +2.7V to +3.6V, GND = 0V, V_AH = 2.4V, V_AL= 0.8V (Note 5),
Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITIONS
Charge Injection, Q
C_L = 1.0nF, V_G = 0V, R_G = 0Ω, (See Figure 2)
OFF Isolation
R_L = 50Ω, C_L = 5pF, f = 1MHz, (See Figure 4)
NO or NC OFF Capacitance, C_OFF f = 1MHz, V_NO or V_NC = V_COM = 0V, (See Figure 6)
COM OFF Capacitance,
C_COM(OFF)
f = 1MHz, V_NO or V_NC = V_COM = 0V, (See Figure 6)
COM ON Capacitance, C_COM(ON) f = 1MHz, V_NO or V_NC = V_COM = 0V, (See Figure 6)
POWER SUPPLY CHARACTERISTICS
TEMP
(°C)
25
25
25
25
(NOTE 6)
MIN
-
-
-
-
TYP
0.5
75
4
11
(NOTE 6)
MAX UNITS
1
pC
-
dB
-
pF
-
pF
25
-
20
-
pF
Positive Supply Current, I+
V+ = 3.6V, V_IN = 0V or V+, all channels on or off
Full
-1
0.0001
1
µA
Electrical Specifications + 12V Supply Test Conditions: V+ = +10.8V to +13.2V, GND = 0V, V_INH = 4V, V_INL = 0.8V (Note 5),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
ON Resistance, R_ON
V+ = 12.0V, I_COM = 1.0mA, V_NO or V_NC = 9V,
(See Figure 5)
R_ON Matching Between Channels, V+ = 12.0V, I_COM = 1.0mA, V_NO or V_NC = 9V, (Note 8)
∆R_ON
R_ON Flatness, R_FLAT(ON)
V+ = 13.2V, I_COM = 1.0mA, V_NO or V_NC = 3V, 6V, 9V,
(Note 9)
NO or NC OFF Leakage Current,
I_NO(OFF) or I_NC(OFF)
V+ = 13.0V, V_COM = 1V, 12V, V_NO or V_NC = 12V, 1V,
(Note 7)
COM OFF Leakage Current,
I_COM(OFF)
V+ = 13.0V, V_COM = 12V, 1V, V_NO or V_NC = 1V, 12V,
(Note 7)
COM ON Leakage Current,
I_COM(ON)
V+ = 13.0V, V_COM = 1V, 12V, or V_NO or V_NC = 1V, 12V,
or floating, (Note 7)
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, V_INH
Input Voltage Low, V_INL
Input Current, I_INH, I_INL
DYNAMIC CHARACTERISTICS
Inhibit Turn-ON Time, t_ON
V+ = 13V, V_IN = 0V or V+
V+ = 10.8V, V_NO or V_NC = 10V, R_L =300Ω, C_L = 35pF,
V_IN = 0 to 4, (See Figure 1)
Inhibit Turn-OFF Time, t_OFF
V+ = 10.8V, V_NO or V_NC = 10V, R_L =300Ω, C_L = 35pF,
V_IN = 0 to 4, (See Figure 1)
Address Transition Time, t_TRANS
V+ = 10.8V, V_NO or V_NC = 10V, R_L =300Ω, C_L = 35pF,
V_IN = 0 to 4, (See Figure 1)
Break-Before-Make Time Delay, t_D V+ = 13.2V, R_L = 300Ω, C_L = 35pF, V_NO or V_NC = 10V,
V_IN = 0 to 4, (See Figure 3)
Charge Injection, Q
C_L = 1.0nF, V_G = 0V, R_G = 0Ω, (See Figure 2)
OFF Isolation
R_L = 50Ω, C_L = 5pF, f = 1MHz, (See Figure 4)
NO or NC OFF Capacitance, C_OFF f = 1MHz, V_NO or V_NC = V_COM = 0V, (See Figure 6)
COM OFF Capacitance,
C_COM(OFF)
f = 1MHz, V_NO or V_NC = V_COM = 0V, (See Figure 6)
COM ON Capacitance, C_COM(ON) f = 1MHz, V_NO or V_NC = V_COM = 0V, (See Figure 6)
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+
V+ = 13.0V, V_IN = 0V or V+, all channels on or off
TEMP (NOTE 6)
(°C)
MIN
Full
0
25
-
Full
-
25
-
Full
-
25
-
Full
-
25
-1
Full
-2.5
25
-1
Full
-2.5
25
-1
Full
-5
Full
2.9
Full
-
Full
-0.5
25
-
Full
-
25
-
Full
-
25
-
Full
-
Full
3
25
-
25
-
25
-
25
-
25
-
Full
-1
TYP
-
45
-
0.5
-
5
-
-
-
-
-
-
-
2.5
2.3
-
25
24
35
9
1.2
75
4
11
20
0.0001
(NOTE 6)
MAX UNITS
V+
V
50
Ω
70
Ω
3
Ω
5
Ω
6
Ω
10
Ω
1
nA
2.5
nA
1
nA
2.5
nA
1
nA
5
nA
-
V
0.8
V
0.5
µA
30
ns
35
ns
28
ns
30
ns
50
ns
55
ns
ns
3
pC
-
dB
-
pF
-
pF
-
pF
1
µA
5
FN6043.3
January 23, 2006