ISL43640_14 Datasheet, PDF (4/13 Pages) Intersil Corporation – Low-Voltage, Single Supply, 4 to 1 Multiplexer, High Performance Analog Switch

ISL43640
Electrical Specifications +5V Supply Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, V_INH = 2.4V, V_INL = 0.8V (Note 5),
Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITIONS
Charge Injection, Q
C_L = 1.0nF, V_G = 0V, R_G = 0Ω, (See Figure 2)
OFF Isolation
R_L = 50Ω, C_L = 5pF, f = 1MHz, (See Figure 4)
NO or NC OFF Capacitance, C_OFF f = 1MHz, V_NO or V_NC = V_COM = 0V, (See Figure 6)
COM OFF Capacitance,
C_COM(OFF)
f = 1MHz, V_NO or V_NC = V_COM = 0V, (See Figure 6)
COM ON Capacitance, C_COM(ON) f = 1MHz, V_NO or V_NC = V_COM = 0V, (See Figure 6)
POWER SUPPLY CHARACTERISTICS
TEMP
(°C)
25
25
25
25
(NOTE 6)
MIN
-
-
-
-
TYP
0.3
75
4
11
(NOTE 6)
MAX UNITS
1
pC
-
dB
-
pF
-
pF
25
-
20
-
pF
Power Supply Range
Full
2
-
12
V
Positive Supply Current, I+
NOTES:
V+ = 5.5V, V_IN = 0V or V+, all channels on or off
Full
-1
0.0001
1
µA
5. V_IN = input voltage to perform proper function.
6. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
7. Leakage parameter is 100% tested at high temp, and guaranteed by correlation at 25°C.
8. ∆R_ON = R_ON (MAX) - R_ON (MIN).
9. Flatness is defined as the difference between the maximum and minimum value of on-resistance over the specified analog signal range.
Electrical Specifications +3V Supply
Test Conditions: V+ = +2.7V to +3.6V, GND = 0V, V_AH = 2.4V, V_AL= 0.8V (Note 5),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
ON Resistance, R_ON
V+ = 3.0V, I_COM = 1.0mA, V_NO or V_NC = 1.5V,
(See Figure 5)
R_ON Matching Between Channels, V+ = 3.0V, I_COM = 1.0mA, V_NO or V_NC = 1.5V, (Note 8)
∆R_ON
R_ON Flatness, R_FLAT(ON)
V+ = 3.0V, I_COM = 1.0mA, V_NO or V_NC = 0.5V, 1.5V,
(Note 9)
NO or NC OFF Leakage Current,
I_NO(OFF) or I_NC(OFF)
V+ = 3.6V, V_COM = 1V, 3V, V_NO or V_NC = 3V, 1V,
(Note 7)
COM OFF Leakage Current,
I_COM(OFF)
V+ = 3.6V, V_COM = 3V, 1V, V_NO or V_NC = 1V, 3V,
(Note 7)
COM ON Leakage Current,
I_COM(ON)
V+ = 3.6V, V_COM = 1V, 3V, or V_NO or V_NC = 1V, 3V, or
floating, (Note 7)
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, V_INH
Input Voltage Low, V_INL
Input Current, I_INH, I_INL
DYNAMIC CHARACTERISTICS
Inhibit Turn-ON Time, t_ON
V+ = 3.6V, V_IN = 0V or V+
V+ = 2.7V, V_NO or V_NC = 1.5V, R_L =300Ω, C_L = 35pF,
V_IN = 0 to 3, (See Figure 1)
Inhibit Turn-OFF Time, t_OFF
V+ = 2.7V, V_NO or V_NC = 1.5V, R_L =300Ω, C_L = 35pF,
V_IN = 0 to 3, (See Figure 1)
Address Transition Time, t_TRANS
V+ = 2.7V, V_NO or V_NC = 1.5V, R_L =300Ω, C_L = 35pF,
V_IN = 0 to 3, (See Figure 1)
Break-Before-Make Time Delay, t_D V+ = 3.6V, R_L = 300Ω, C_L = 35pF, V_NO or V_NC = 1.5V,
V_IN = 0 to 3, (See Figure 3)
TEMP
(°C)
Full
25
Full
25
Full
25
Full
25
Full
25
Full
25
Full
Full
Full
Full
25
Full
25
Full
25
Full
Full
(NOTE 6)
MIN
0
-
-
-
-
-
-
-1
-2.5
-1
-2.5
-1
-5
2.0
-
-0.5
-
-
-
-
-
-
15
TYP
-
190
-
1
-
48
-
-
-
-
-
-
-
1.0
0.8
-
144
-
53
-
145
-
35
(NOTE 6)
MAX UNITS
V+
V
220
Ω
250
Ω
3
Ω
5
Ω
90
Ω
90
Ω
1
nA
2.5
nA
1
nA
2.5
nA
1
nA
5
nA
-
V
0.5
V
0.5
µA
155
ns
175
ns
60
ns
65
ns
160
ns
190
ns
-
ns
4
FN6043.3
January 23, 2006