|
82C88 Datasheet, PDF (5/10 Pages) Intersil Corporation – CMOS Bus Controller | |||
|
◁ |
82C88
Absolute Maximum Ratings
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8.0V
Input, Output or I/O Voltage . . . . . . . . . . . GND -0.5V to VCC +0.5V
ESD Classiï¬cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
Operating Conditions
Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V
Operating Temperature Range
C82C88. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to +70oC
I82C88 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to +85oC
M82C88 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to +125oC
Thermal Information
Thermal Resistance (Typical)
θJA (oC/W) θJC (oC/W)
CERDIP Package . . . . . . . . . . . . . . . . 75
18
CLCC Package . . . . . . . . . . . . . . . . . . 85
22
PDIP Package . . . . . . . . . . . . . . . . . . . 75
N/A
PLCC Package . . . . . . . . . . . . . . . . . . 75
N/A
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65oC to +150oC
Maximum Junction Temperature
Ceramic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC
Plastic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . +300oC
(PLCC - Lead Tips Only)
Die Characteristics
Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Gates
CAUTION: Stresses above those listed in âAbsolute Maximum Ratingsâ may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this speciï¬cation is not implied.
DC Electrical Speciï¬cations
VCC
TA =
TA =
= 5.0V ± 10%;
0oC to +70oC (C82C88);
-40oC to +85oC (I82C88);
TA = -55oC to +125oC (M82C88)
SYMBOL
PARAMETER
MIN
MAX
UNITS
TEST CONDITIONS
VIH
Logical One Input Voltage
2.0
-
V
C82C88, I82C88
2.2
-
V
M82C88
VIL
Logical Zero Input Voltage
-
0.8
V
VIHC CLK Logical One Input Voltage
VCC -0.8
-
V
VILC CLK Logical Zero Input Voltage
-
0.8
V
VOH
VOL
Output High Voltage
Command Outputs
Output High Voltage
Control Outputs
Output Low Voltage
Command Outputs
3.0
-
VCC -0.4
3.0
-
VCC -0.4
-
0.5
V
IOH = -8.0mA
V
IOH = -2.5mA
V
IOH = -4.0mA
V
IOH = -2.5mA
V
IOL= +12.0mA
Output Low Voltage
Control Outputs
-
0.4
V
IOL = +8.0mA
II
Input Leakage Current
-1.0
1.0
µA
VIN = GND or VCC, except S0, S1, S2,
DIP Pins 1-2, 6, 15
IBHH
IO
Input Leakage Current-Status Bus
Output Leakage Current
-50
-10.0
-300
10.0
µA
VIN = 2.0V, S0, S1, S2 (See Note 1)
µA
VO = GND or VCC, IOB = GND, AEN = VCC,
DIP Pins 7-9, 11-14
ICCSB Standby Power Supply
-
10
µA
VCC = 5.5V, VIN = VCC or GND, Outputs Open
ICCOP Operating Power Supply Current
-
1
mA/MHz VCC = 5.5V, Outputs Open (See Note 2)
NOTES:
1. IBHH should be measured after raising the VIN on S0, S1, S2 to VCC and then lowering to valid input high level of 2.0V.
2. ICCOP = 1mA/MHz of CLK cycle time (TCLCL)
Capacitance TA = +25oC
SYMBOL
PARAMETER
CIN
Input Capacitance
COUT
Output Capacitance
TYPICAL
10
17
UNITS
pF
pF
TEST CONDITIONS
FREQ = 1MHz, all measurements are
referenced to device GND
4-337
|
▷ |