X9252 Datasheet, PDF (4/19 Pages) Xicor Inc. – Quad Digitally-Controlled (XDCP) potentiometer

X9252
Absolute Maximum Ratings
Junction Temperature under bias. . . . . . . . . . . . . . .-65°C to +135°C
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage at any digital interface pin
with respect to V_SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1V to +7V
V_CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1V to +7V
Voltage at any DCP pin with
respect to V_SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1V to V_CC
Lead temperature (soldering, 10s). . . . . . . . . . . . . . . . . . . . . . 300°C
I_W (10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA
Recommended Operating Conditions
Commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
Industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Supply Voltage (V_CC)(Note 4) Limits . . . . . . . . . . . . . . . 2.7V to 5.5V
CAUTION: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional operation
of the device (at these or any other conditions above those listed in the operational sections of this specification) is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
Analog Specifications Over recommended operating conditions unless otherwise stated.
SYMBOL
R_TOTAL
PARAMETER
End to end resistance
End to end resistance tolerance
Power rating
R_TOTAL DCP to DCP resistance matching
Matching
I_W (Note 5) Wiper current
R_W
Wiper resistance
V_TERM
Voltage on any DCP pin
Noise (Note 5)
Resolution
Absolute linearity (Note 1)
Relative linearity (Note 2)
TEST CONDITIONS
MIN
Y, W, U, T versions respectively
-20
25°C, each DCP
See test circuit
-3.0
Wiper current =
V_CC
R_TOTAL
Vss
Ref: 1kHz
V(R_H0)=V(R_H1)=V(R_H2)=V(R_H3)=V_CC
-1
V(R_L0)=V(R_L1)=V(R_L2)=V(R_L3)=V_SS
-0.3
Temperature coefficient of resistance
(Note 5)
Ratiometric Temperature (Note 5)
-20
Coefficient
C_H/C_L/C_W Potentiometer Capacitance (Note 5)
I_OL
Leakage on DCP pins
See equivalent circuit
Voltage at pin from V_SS to V_CC
TYP
(Note 4)
2.8, 10,
50, 100
0.75
50
-120
0.4
±300
10/10/25
0.1
MAX
+20
50
2.0
+3.0
150
Vcc
+1
+0.3
+20
10
UNIT
kΩ
%
mW
%
mA
Ω
V
dBV
%
MI
(Note 3)
MI
(Note 3)
ppm/°C
ppm/°C
pF
µA
DC Electrical Specifications Over the recommended operating conditions unless otherwise specified.
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
I_CC1
V_CC supply current (Volatile write/read) f_SCL = 400kHz;SDA = Open; (for 2-Wire, Active,
Read and Volatile Write States only)
I_CC2
V_CC supply current (active)
f_SCL = 200kHz;
(for U/D interface, increment, decrement)
I_CC3
V_CC supply current (nonvolatile write)
f_SCL = 400kHz; SDA = Open;
(for 2-Wire, Active, Nonvolatile Write State only)
I_SB
V_CC current (standby)
V_CC = +5.5V; V_IN = V_SS or V_CC; SDA = V_CC;
(for 2-Wire, Standby State only)
MAX
3
UNITS
mA
3
mA
5
mA
20
µA
4
FN8167.1
September 14, 2005