ISL5120 Datasheet, PDF (4/15 Pages) Intersil Corporation – Low-Voltage, Single Supply, Dual SPST, SPDT Analog Switches

ISL5120, ISL5121, ISL5122, ISL5123
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to15V
Input Voltages
IN (Note 3). . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
NO, NC (Note 3) . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . 40mA
ESD Rating (Per MIL-STD-883 Method 3015). . . . . . . . . . . . . .>2kV
Operating Conditions
Temperature Range
ISL512XCX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
ISL512XIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
Thermal Information
Thermal Resistance (Typical, Note 4)
θ_JA (°C/W)
6 Ld SOT-23 Package . . . . . . . . . . . . . . . . . . . . . . .
230
8 Ld SOT-23 Package . . . . . . . . . . . . . . . . . . . . . . .
215
8 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . .
170
Maximum Junction Temperature (Plastic Package). . . . . . . . 150°C
Moisture Sensitivity (See Technical Brief TB363)
All Other Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 1
8 Ld SOT-23 Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 2
Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
2. Signals on NC, NO, COM, or IN exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
3. θ_JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications - 5V Supply Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, V_INH = 2.4V, V_INL = 0.8V (Note 5),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP (NOTE 6)
(NOTE 6)
(°C)
MIN
TYP
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
ON Resistance, R_ON
V+ = 4.5V, I_COM = 1.0mA, V_NO or V_NC = 3.5V,
(See Figure 5)
Full
0
25
-
Full
-
-
V+
V
19
30
Ω
23
40
Ω
R_ON Matching Between Channels, V+ = 5V, I_COM = 1.0mA, V_NO or V_NC= 3.5V
∆R_ON
25
-
0.8
2
Ω
Full
-
1
4
Ω
R_ON Flatness, R_FLAT(ON)
V+ = 5V, I_COM = 1.0mA, V_NO or V_NC = 1V, 2V, 3V
Full
-
NO or NC OFF Leakage Current, V+ = 5.5V, V_COM = 1V, 4.5V, V_NO or V_NC = 4.5V, 1V,
25
-0.1
I_NO(OFF) or I_NC(OFF)
(Note 7)
Full
-5
7
0.01
-
8
Ω
0.1
nA
5
nA
COM OFF Leakage Current,
V+ = 5.5V, V_COM = 4.5V, 1V, V_NO or V_NC = 1V, 4.5V,
25
-0.1
-
0.1
nA
I_COM(OFF)
(Note 7)
Full
-5
-
5
nA
COM ON Leakage Current,
I_COM(ON)
V+ = 5.5V, V_COM = 1V, 4.5V, or V_NO or V_NC = 1V, 4.5V, 25
-0.2
-
0.2
nA
or Floating, (Note 7)
Full
-10
-
10
nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, t_ON
V_NO or V_NC = 3V, R_L =1kΩ, C_L = 35pF, V_IN = 0 to 3V, 25
-
(See Figure 1)
Full
-
28
75
ns
40
150
ns
Turn-OFF Time, t_OFF
V_NO or V_NC = 3V, R_L =1kΩ, C_L = 35pF, V_IN = 0 to 3V, 25
-
(See Figure 1)
Full
-
20
50
ns
30
100
ns
Break-Before-Make Time Delay
R_L = 300Ω, C_L = 35pF, V_NO = V_NC = 3V, V_IN = 0 to 3V, Full
3
10
-
ns
(ISL5122, ISL5123), t_D
(See Figure 3)
Charge Injection, Q
C_L = 1.0nF, V_G = 0V, R_G = 0Ω, (See Figure 2)
25
-
3
5
pC
OFF Isolation
R_L = 50Ω, C_L = 5pF, f = 1MHz, (See Figure 4)
25
-
76
-
dB
Crosstalk (Channel-to-Channel)
R_L = 50Ω, C_L = 5pF, f = 1MHz, (See Figure 6)
25
-
-105
-
dB
4
FN6022.6
November 17, 2004