ISL43L410 Datasheet, PDF (4/11 Pages) Intersil Corporation – Ultra Low ON-Resistance, Low Voltage, Single Supply, DPDT Analog Switch

ISL43L410
Electrical Specifications - 3V Supply
Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, V_INH = 1.4V, V_INL = 0.5V (Note 4, 6),
Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITIONS
TEMP (NOTE 5)
(NOTE 5)
(°C)
MIN
TYP
MAX UNITS
POWER SUPPLY CHARACTERISTICS
Power Supply Range
Full
1.65
3.6
V
Positive Supply Current, I+
V+ = +1.65 to 3.6V, V_IN = 0V or V+
25
-
Full
-
-
40
nA
-
750
nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V_INL
Input Voltage High, V_INH
Input Current, I_INH, I_INL
NOTES:
V+ = 3.3V, V_IN = 0V or V+ (Note 8)
Full
-
-
Full
1.4
-
Full
-0.5
-
0.5
V
-
V
0.5
µA
4. V_IN = input voltage to perform proper function.
5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
6. Parts are 100% tested at +25°C. Limits across the full temperature range are guaranteed by design and correlation.
7. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
8. Guaranteed but not tested.
9. R_ON matching between channels is calculated by subtracting the channel with the highest max Ron value from the channel with lowest max Ron
value.
Electrical Specifications - 1.8V Supply
Test Conditions: V+ = +1.65V to +2V, GND = 0V, V_INH = 1.0V, V_INL = 0.4V (Note 4, 6),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
ON Resistance, R_ON
V+ = 1.8V, I_COM = 100mA, V_NO or V_NC = 0V to V+,
See Figure 5, Note 8
NO or NC OFF Leakage Current,
I_NO(OFF) or I_NC(OFF)
COM ON Leakage Current,
I_COM(ON)
DYNAMIC CHARACTERISTICS
Turn-ON Time, t_ON
V+ = 2.0V, V_COM = 0.3V, 1.8V, V_NO or V_NC = 1.8V, 0.3V
V+ = 2.0V, V_COM = 0.3V, 1.8V, or V_NO or V_NC = 0.3V,
1.8V
V+ = 1.65V, V_NO or V_NC = 1.0V, R_L =50Ω, C_L = 35pF,
See Figure 1, Note 8
Turn-OFF Time, t_OFF
V+ = 1.65V, V_NO or V_NC = 1.0V, R_L =50Ω, C_L = 35pF,
See Figure 1, Note 8
Break-Before-Make Time Delay, t_D
Charge Injection, Q
OFF Isolation
Crosstalk (Channel-to-Channel)
V+ = 2.0V, V_NO or V_NC = 1.0V, R_L =50Ω, C_L = 35pF,
See Figure 3, Note 8
C_L = 1.0nF, V_G = 0V, R_G = 0Ω, See Figure 2
R_L = 50Ω, C_L = 5pF, f = 100kHz, V_COM = 1V_RMS,
See Figure 4
R_L = 50Ω, C_L = 5pF, f = 100kHz, V_COM = 1V_RMS,
See Figure 6
TEMP
(°C)
Full
25
Full
25
Full
25
Full
25
Full
25
Full
Full
25
25
25
(NOTE 5)
MIN
0
-
-
-2
-40
-3
-60
-
-
-
-
2
-
-
-
TYP
-
0.4
-
-
-
-
-
22
-
9
-
9
49
68
-95
(NOTE 5)
MAX UNITS
V+
V
0.6
Ω
0.6
Ω
2
nA
40
nA
3
nA
60
nA
28
ns
33
ns
15
ns
20
ns
-
ns
-
pC
-
dB
-
dB
NO or NC OFF Capacitance, C_OFF f = 1MHz, V_NO or V_NC = V_COM = 0V, See Figure 7
25
-
115
-
pF
COM ON Capacitance, C_COM(ON) f = 1MHz, V_NO or V_NC = V_COM = 0V, See Figure 7
25
-
224
-
pF
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V_INL
Input Voltage High, V_INH
Input Current, I_INH, I_INL
V+ = 2.0V, V_IN = 0V or V+ (Note 8)
Full
-
-
Full
1.0
-
Full
-0.5
-
0.4
V
-
V
0.5
µA
4
FN6090.1
November 3, 2004