English
Language : 

ISL43L410 Datasheet, PDF (3/11 Pages) Intersil Corporation – Ultra Low ON-Resistance, Low Voltage, Single Supply, DPDT Analog Switch
◁
ISL43L410
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 4.7V
Input Voltages
NO, NC, ADD, INH (Note 2) . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current NO, NC, or COM . . . . . . . . . . . . . . . . . ±300mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . ±500mA
ESD Rating:
HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>9kV
MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>500V
CDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>1kV
Thermal Information
Thermal Resistance (Typical, Note 3)
θJA (°C/W)
10 Ld 3x3 DFN Package . . . . . . . . . . . . . . . . . . . . .
110
10 Ld MSOP Package . . . . . . . . . . . . . . . . . . . . . . .
190
Maximum Junction Temperature (Plastic Package). . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(Lead Tips Only)
Operating Conditions
Temperature Range
ISL43L410IX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
2. Signals on NC, NO, ADD, INH, or COM exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current
ratings.
3. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications - 3V Supply
Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.5V (Note 4, 6),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
ON Resistance, RON
V+ = 2.7V, ICOM = 100mA, VNO or VNC = 0V to V+,
See Figure 5
RON Matching Between Channels, V+ = 2.7V, ICOM = 100mA, VNO or VNC= Voltage at max
∆RON
RON, Note 9
RON Flatness, RFLAT(ON)
V+ = 2.7V, ICOM = 100mA, VNO or VNC = 0V to V+,
Note 7
NO or NC OFF Leakage Current,
INO(OFF) or INC(OFF)
COM ON Leakage Current,
ICOM(ON)
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
V+ = 3.3V, VCOM = 0.3V, 3V, VNO or VNC = 3V, 0.3V
V+ = 3.3V, VCOM = 0.3V, 3V, or VNO or VNC = 0.3V, 3V
V+ = 2.7V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF,
See Figure 1, Note 8
Turn-OFF Time, tOFF
V+ = 2.7V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF,
See Figure 1, Note 8
Break-Before-Make Time Delay, tD V+ = 3.3V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF,
See Figure 3, Note 8
Charge Injection, Q
OFF Isolation
CL = 1.0nF, VG = 0V, RG = 0Ω, See Figure 2
RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS,
See Figure 4
Crosstalk (Channel-to-Channel)
RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS,
See Figure 6
Total Harmonic Distortion
NO or NC OFF Capacitance, COFF
COM ON Capacitance, CCOM(ON)
f = 20Hz to 20kHz, VCOM = 2VP-P, RL = 600Ω
f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7
f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7
TEMP
(°C)
Full
25
Full
25
Full
25
Full
25
Full
25
Full
25
Full
25
Full
Full
25
25
25
25
25
25
(NOTE 5)
MIN
0
-
-
-
-
-
-
-2
-40
-3
-60
-
-
-
-
2
-
-
-
-
-
-
TYP
-
0.29
-
0.03
-
0.03
-
-
-
-
-
14
-
6
-
7
95
68
-95
0.003
115
224
(NOTE 5)
MAX UNITS
V+
V
0.4
Ω
0.4
Ω
0.06
Ω
0.06
Ω
0.1
Ω
0.1
Ω
2
nA
40
nA
3
nA
60
nA
20
ns
25
ns
12
ns
17
ns
-
ns
-
pC
-
dB
-
dB
-
%
-
pF
-
pF
3
FN6090.1
November 3, 2004
 ▷