ISL43L110 Datasheet, PDF (4/11 Pages) Intersil Corporation – Ultra Low ON-Resistance, +1.1V to +4.5V Single Supply, SPST Analog Switches

ISL43L110, ISL43L111
Electrical Specifications - 4.3V Supply
Test Conditions: V+ = +3.9V to +4.5V, GND = 0V, V_INH = 1.6V, V_INL = 0.5V (Notes 4, 6),
Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITIONS
TEMP (NOTE 5)
(NOTE 5)
(°C)
MIN
TYP
MAX UNITS
POWER SUPPLY CHARACTERISTICS
Power Supply Range
Full
1.1
4.5
V
Positive Supply Current, I+
V+ =+4.5V, V_IN = 0V or V+
25
-
Full
-
-
0.05
µA
-
0.4
µA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V_INL
Full
-
-
0.5
V
Input Voltage High, V_INH
Full
1.6
-
-
V
Input Current, I_INH, I_INL
V+ = 4.5V, V_IN = 0V or V+ (Note 8)
Full
-0.5
-
0.5
µA
NOTES:
4. V_IN = input voltage to perform proper function.
5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
6. Parts are 100% tested at +25°C. Limits across the full temperature range are guaranteed by design and correlation.
7. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
8. Guaranteed but not tested.
Electrical Specifications - 3V Supply
Test Conditions: V+ = +2.7V to +3.6V, GND = 0V, V_INH = 1.4V, V_INL = 0.5V (Notes 4, 6),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP (NOTE 5)
(NOTE 5)
(°C)
MIN
TYP
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
ON Resistance, R_ON
V+ = 2.7V, I_COM = 100mA, V_NO or V_NC = 1.5V
(See Figure 4)
Full
0
-
V+
V
25
-
0.26
0.4
Ω
Full
-
-
0.45
Ω
R_ON Flatness, R_FLAT(ON)
V+ = 2.7V, I_COM = 100mA, V_NO or V_NC = 0.6V, 1.5V,
25
-
0.038
0.07
Ω
2.1V (Note 7)
Full
-
-
0.09
Ω
NO or NC OFF Leakage Current, V+ = 3.3V, V_COM = 0.3V, 3V, V_NO or V_NC = 3V, 0.3V
25
-
1.8
-
nA
I_NO(OFF) or I_NC(OFF)
Full
-
8
-
nA
COM ON Leakage Current,
I_COM(ON)
V+ = 3.3V, V_COM = 0.3V, 3V, or V_NO or V_NC = 0.3V, 3V, 25
-
1.8
-
nA
or Floating
Full
-
16
-
nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, t_ON
V+ = 2.7V, V_NO or V_NC = 1.5V, R_L = 50Ω, C_L = 35pF
25
-
(See Figure 1, Note 8)
Full
-
9
15
ns
-
20
ns
Turn-OFF Time, t_OFF
V+ = 2.7V, V_NO or V_NC = 1.5V, R_L = 50Ω, C_L = 35pF
25
-
(See Figure 1, Note 8)
Full
-
6
12
ns
-
15
ns
Charge Injection, Q
OFF Isolation
V_G = V+/2, R_G = 0Ω,C_L = 1.0nF (See Figure 2)
25
-
72
-
pC
R_L = 50Ω, C_L = 5pF, f = 100kHz, V_COM = 1V_RMS
25
-
-65
-
dB
(See Figure 3)
Total Harmonic Distortion
f = 20Hz to 20kHz, V_COM = 2V_P-P, R_L = 32Ω
25
NO or NC or COM OFF
Capacitance, C_OFF
f = 1MHz, V_NO or V_NC = V_COM = 0V (See Figure 5)
25
COM ON Capacitance, C_COM(ON) f = 1MHz, V_NO or V_NC = V_COM = 0V (See Figure 5)
25
-
0.003
-
%
-
68
-
pF
-
160
-
pF
4
FN6130.0
March 15, 2005