ISL43L110 Datasheet, PDF (3/11 Pages) Intersil Corporation – Ultra Low ON-Resistance, +1.1V to +4.5V Single Supply, SPST Analog Switches

ISL43L110, ISL43L111
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 4.7V
Input Voltages
NO, NC, IN (Note 2) . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current NO, NC, or COM . . . . . . . . . . . . . . . . . ±300mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . ± 600mA
ESD Rating:
HBM > . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>4kV
MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>300V
CDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>1000V
Thermal Information
Thermal Resistance (Typical, Note 3)
θ_JA (°C/W)
5 Ld SC70 Package . . . . . . . . . . . . . . . . . . . . . . . . .
660
Maximum Junction Temperature (Plastic Package). . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(Lead Tips Only)
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
2. Signals on NC, NO, IN, or COM exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
3. θ_JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications - 4.3V Supply
Test Conditions: V+ = +3.9V to +4.5V, GND = 0V, V_INH = 1.6V, V_INL = 0.5V (Notes 4, 6),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP (NOTE 5)
(NOTE 5)
(°C)
MIN
TYP
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
ON Resistance, R_ON
V+ = 3.9V, I_COM = 100mA, V_NO or V_NC = 2.2V
(See Figure 4)
Full
0
-
V+
V
25
-
0.22
-
Ω
Full
-
0.25
-
Ω
R_ON Flatness, R_FLAT(ON)
V+ = 3.9V, I_COM = 100mA, V_NO or V_NC = 0.8V, 2.2V,
25
-
0.03
-
Ω
3.5V, (Note 7)
Full
-
0.05
-
Ω
NO or NC OFF Leakage Current, V+ = 4.5V, V_COM = 0.3V, 3V, V_NO or V_NC = 3V, 0.3V
25
-30
-
30
nA
I_NO(OFF) or I_NC(OFF)
Full
-200
-
200
nA
COM ON Leakage Current,
I_COM(ON)
V+ = 4.5V, V_COM = 0.3V, 3V, or V_NO or V_NC = 0.3V, 3V, 25
-3
-
or Floating
Full
-35
-
3
nA
35
nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, t_ON
V+ = 3.9V, V_NO or V_NC = 1.5V, R_L = 50Ω, C_L = 35pF
25
-
(See Figure 1, Note 8)
Full
-
8
15
ns
-
20
ns
Turn-OFF Time, t_OFF
V+ = 3.9V, V_NO or V_NC = 1.5V, R_L = 50Ω, C_L = 35pF
25
-
(See Figure 1, Note 8)
Full
-
5
10
ns
-
15
ns
Charge Injection, Q
OFF Isolation
V_G = V+/2, R_G = 0Ω, C_L = 1.0nF (See Figure 2)
25
-
89
-
pC
R_L = 50Ω, C_L = 5pF, f = 100kHz, V_COM = 1V_RMS,
25
-
-65
-
dB
(See Figure 3)
Total Harmonic Distortion
f = 20Hz to 20kHz, V_COM = 2V_P-P, R_L = 32Ω
25
NO or NC OFF Capacitance, C_OFF f = 1MHz, V_NO or V_NC = V_COM = 0V (See Figure 5)
25
COM ON Capacitance, C_COM(ON) f = 1MHz, V_NO or V_NC = V_COM = 0V (See Figure 5)
25
-
0.003
-
%
-
68
-
pF
-
160
-
pF
3
FN6130.0
March 15, 2005