HC5517_00 Datasheet, PDF (4/19 Pages) Intersil Corporation – 3 REN Ringing SLIC For ISDN Modem/TA and WLL

HC5517
Electrical Specifications
Unless Otherwise Specified, Typical Parameters are at T_A = 25^oC, Min-Max Parameters are over
Operating Temperature Range, V_BAT = -24V, V_CC = +5V, AGND = BGND = 0V. All AC Parameters are
specified at 600Ω 2-Wire terminating impedance. (Continued)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNITS
Dial Pulse Distortion (Note 3)
-
0.1
0.5
ms
Uncommitted Relay Driver
On Voltage V_OL
Off Leakage Current
I_OL (RDO) = 30mA
-
0.2
0.5
V
-
±10
±100
µA
TTL/CMOS Logic Inputs (F0, F1, RS, TST, RDI)
Logic ‘0’ V_IL
Logic ‘1’ V_IH
Input Current (F0, F1, RS, TST, RDI)
Input Current (F0, F1, RS, TST, RDI)
Logic Outputs
Logic ‘0’ V_OL
Logic ‘1’ V_OH
Power Dissipation On Hook
Power Dissipation Off Hook
I_CC
I_BAT
UNCOMMITTED OP AMP PARAMETERS
IIH, 0V ≤ V_IN ≤ 5V
IIL, 0V ≤ V_IN ≤ 5V
I_LOAD = 800µA
I_LOAD = 40µA
V_CC = +5V, V_BAT = -80V, R_LOOP = ∞
V_CC = +5V, V_BAT = -48V, R_LOOP = ∞
V_CC = +5V, V_BAT = -24V, R_LOOP = 600Ω,
I_L = 25mA
V_CC = +5V, V_BAT = -80V, R_LOOP = ∞
V_CC = +5V, V_BAT = -48V, R_LOOP = ∞
V_CC = +5V, V_BAT = -24V, R_LOOP = ∞
V_CC = +5V, V_B- = -80V, R_LOOP = ∞
V_CC = +5V, V_B- = -48V, R_LOOP = ∞
V_CC = +5V, V_B- = -24V, R_LOOP = ∞
0
-
0.8
V
2.0
-
5.5
V
-
-
-1
µA
-
-
-100
µA
-
0.1
0.5
V
2.7
-
-
V
-
300
-
mW
-
150
-
mW
-
280
-
mW
-
3
6
mA
-
2
5
mA
-
1.9
4
mA
-
3.6
7
mA
-
2.6
6
mA
-
1.8
4
mA
Input Offset Voltage
-
±5
-
mV
Input Offset Current
-
±10
-
nA
Differential Input Resistance (Note 3)
-
1
-
MΩ
Output Voltage Swing (Note 3)
Small Signal GBW (Note 3)
R_L = 10kΩ
-
±3
-
V_P-P
-
1
-
MHz
NOTES:
3. These parameters are controlled by design or process parameters and are not directly tested. These parameters are characterized upon initial
design release, upon design changes which would affect these characteristics, and at intervals to assure product quality and specification com-
pliance.
4. For transhybrid circuit as shown in Figure 10.
5. Application limitation based on maximum switch hook detect limit and metallic currents. Not a part limitation.
4