HA5023883 Datasheet, PDF (4/19 Pages) Intersil Corporation – Dual 125MHz Video Current Feedback Amplifier

Specifications HA5023/883
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Characterized at: V_SUPPLY = ±5V, A_V = +2, R_F = 681Ω, R_L = 400Ω, Unless Otherwise Specified.
LIMITS
PARAMETERS
SYMBOL
CONDITIONS
NOTES TEMPERATURE MIN MAX UNITS
-3dB Bandwidth
Gain Flatness
Slew Rate
Rise and Fall Time
Overshoot
Propagation Delay
BW(+1) A_V = +1, R_F = 1K
1
V_OUT = 100mV_RMS
BW(+2) A_V = +2,
1
V_OUT = 100mV_RMS
GF5
A_V = +2, f ≤5MHz
1
V_OUT = 100mV_RMS
GF10 A_V = +2, f ≤10MHz
1
V_OUT = 100mV_RMS
GF20 A_V = +2, f ≤20MHz
1
V_OUT = 100mV_RMS
+SR(+1) A_V = +1, R_F = 1K
1, 4
V_OUT = -2V to +2V
-SR(+1) A_V = +1, R_F = 1K
1, 4
V_OUT = +2V to -2V
+SR(+2) A_V = +2, V_OUT = -2V to +2V
1, 4
-SR(+2) A_V = +2, V_OUT = +2V to -2V
1, 4
T_R
A_V = +2, V_OUT = -0.5V to +0.5V
1, 2
T_F
A_V = +2, V_OUT = +0.5V to -0.5V
1, 2
+OS
A_V = +2, V_OUT = -0.5V to +0.5V
1, 3
-OS
A_V = +2, V_OUT = +0.5V to -0.5V
1, 3
+T_P
A_V = +2, R_F = 681Ω
1, 2
V_OUT = 0V to 1V
-T_P
A_V = +2, R_F = 681Ω
1, 2
V_OUT = 1V to 0V
+125^oC, -55^oC
+125^oC, -55^oC
+125^oC, -55^oC
+125^oC, -55^oC
+125^oC, -55^oC
+125^oC, -55^oC
+125^oC, -55^oC
+125^oC, -55^oC
+125^oC, -55^oC
+125^oC, -55^oC
+125^oC, -55^oC
+125^oC, -55^oC
+125^oC, -55^oC
+125^oC, -55^oC
+125^oC, -55^oC
62
-
MHz
62
-
MHz
-
±0.045
dB
-
±0.085
dB
-
±0.65
dB
250
-
V/µs
240
-
V/µs
400
-
V/µs
360
-
V/µs
-
6.5
ns
-
6.5
ns
-
35
%
-
27
%
-
9.5
ns
-
9.0
ns
NOTES:
1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These param-
eters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization
based upon data from multiple production runs which reflect lot-to-lot and within lot variation.
2. Measured between 10% and 90% points.
3. For 200ps input transition times. Overshoot decreases as input transition times increase, especially for A_V = +1. Please refer to
Performance Curves.
4. Measured between 25% and 75% points.
TABLE 4. ELECTRICAL TEST REQUIREMENTS
MIL-STD-883 TEST REQUIREMENTS
SUBGROUPS (SEE TABLE 1)
Interim Electrical Parameters (Pre Burn-In)
Final Electrical Test Parameters
Group A Test Requirements
1
1 (Note 1), 2, 3, 4
1, 2, 3, 4
Groups C and D Endpoints
1
NOTE:
1. PDA applies to Subgroup 1 only.
Spec Number 511108-883
4