HA2556 Datasheet, PDF (4/20 Pages) Intersil Corporation – Wideband Four Quadrant Analog Multiplier (Voltage Output)

Specifications HA2556/883
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued)
Device Tested: at V_SUPPLY = ±15V, R_F = 50Ω, R_L = 1kΩ, C_L = 20pF, Unless Otherwise Specified.
LIMITS
PARAMETERS
Overshoot
Slew Rate
Differential Input
Resistance
SYMBOL
+OS, -OS
CONDITIONS
V_Y = 200mV step,
V_X = 5V
+SR, -SR V_Y = 10V step,
V_X = 5V
R_IN (V_Y) V_Y = ±5V, V_X = 0V
NOTES
1
1
1
1
1
TEMPERATURE
+25^oC
+125^oC, -55^oC
+25^oC
+125^oC, -55^oC
+25^oC
MIN MAX UNITS
-
35
%
-
50
%
410
-
V/µs
360
-
V/µs
650
-
kΩ
V_X CHARACTERISTICS
Bandwidth
BW (V_X) -3dB, V_Y = 5V,
1
V_X ≤ 200mV_P-P
+25^oC
30
-
MHz
Gain Flatness
GF (V_X) 0.1dB, V_Y = 5V,
1
V_X ≤ 200mV_P-P
+25^oC
2.0
-
MHz
AC Feedthrough
V_ISO
f_O = 5MHz,
1, 3
V_X = 200mV_P-P
V_Y = Nulled
+25^oC
-
- 45
dB
Rise & Fall Time
T_R, T_F
V_X = 200mV step,
1
+25^oC
-
9.5
ns
V_Y = 5V,
10% to 90% pts
1
+125^oC, -55^oC
-
10
ns
Overshoot
+OS, -OS V_X = 200mV step,
1
+25^oC
-
35
%
V_Y = 5V
1
+125^oC, -55^oC
-
50
%
Slew Rate
+SR, -SR V_X = 10V step,
V_Y = 5V
1
+25^oC
410
-
V/µs
1
+125^oC, -55^oC
360
-
V/µs
Differential Input
Resistance
R_IN (V_X) V_X = ±5V, V_Y = 0V
1
+25^oC
650
-
kΩ
OUTPUT CHARACTERISTICS
Output Resistance
R_OUT
V_Y = ±5V, V_X = 5V
1
R_L = 1kΩ to 250Ω
+25^oC
-
1
Ω
NOTES:
1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These param-
eters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization
based upon data from multiple production runs which reflect lot to lot and within lot variation.
2. V_Z AC characteristics may be implied from V_Y due to the use of V_Z as feedback in the test circuit.
3. Offset voltage applied to minimize feedthrough signal.
TABLE 4. ELECTRICAL TEST REQUIREMENTS
MIL-STD-883 TEST REQUIREMENTS
SUBGROUPS (SEE TABLE 1)
Interim Electrical Parameters (Pre Burn-In)
-
Final Electrical Test Parameters
1 (Note 1), 2, 3
Group A Test Requirements
1, 2, 3
Groups C and D Endpoints
1
NOTE:
1. PDA applies to Subgroup 1 only. No other subgroups are included in PDA.
Spec Number 511063-883
8-10