ISL59420_14 Datasheet, PDF (3/13 Pages) Intersil Corporation – 400MHz Multiplexing Amplifier

ISL59420
Absolute Maximum Ratings (T_A = 25°C)
Supply Voltage (V+ to V-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V- -0.5V, V+ +0.5V
Supply Turn-on Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1V/μs
IN- Input Current (Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA
Digital & Analog Input Current (Note 4). . . . . . . . . . . . . . . . . . . . . . . . 50mA
Output Current (Continuous) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA
ESD Rating
Human Body Model (Per MIL-STD-883 Method 3015.7). . . . . . . . . .2.5kV
Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300V
Thermal Information
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Ambient Operating Temperature . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . .-40°C to +125°C
Power Dissipation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
θ_JA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .See Figures 22 and 23 on page 8
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTE:
4. If an input signal is applied before the supplies are powered up, the input current must be limited to these maximum values.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise
noted, all tests are at the specified temperature and are pulsed tests, therefore: T_J = T_C = T_A
Electrical Specifications V+ = +5V, V- = -5V, GND = 0V, T_A = 25°C, R_L = 500Ω to GND unless otherwise specified.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
MAX
(NOTE 5) TYP (NOTE 5) UNIT
GENERAL
±I_S Enabled
I_S Disabled
V_OUT
I_OUT
V_OS
Ib+
Ib-
Supply Current
Disabled Supply Current I+
Disabled Supply Current I-
Positive Output Swing
Negative Output Swing
Output Current
Output Offset Voltage
Input Bias Current
Feedback Bias Current
No load, V_IN = 0V, ENABLE Low
No load, V_IN = 0V, ENABLE High
No load, V_IN = 0V, ENABLE High
V_IN = 2V, R_L = 500Ω, A_V = 2
V_IN = -2V, R_L = 500Ω, A_V = 2
R_L = 10Ω to GND
V_IN = 0V
9.5
11
15
mA
0.5
1
1.5 mA
3
10
μA
3.5 3.9
V
-3
-2.8
V
80 130
mA
-12
4
+12 mV
-4
-2.5 -1.5
μA
-15
7
15
μA
R_out
R_IN
A_CL or A_V
I_TRI
LOGIC
Output Resistance
Input Resistance
Voltage Gain
Output Current in Three-state
HIZ = logic high, (DC), A_V = 1
HIZ = logic low, (DC), A_V = 1
V_IN = 3.5V
R_F = R_G = 600Ω, V_OUT = ±3V
V_OUT = 0V
1.4
MΩ
0.2
Ω
10
MΩ
1.990 2.005 2.020 V/V
-20
6
20
μA
V_H
V_L
I_IH
I_IL
AC GENERAL
Input High Voltage (Logic Inputs)
Input Low Voltage (Logic Inputs)
Input High Current (Logic Inputs)
Input Low Current (Logic Inputs)
2
V
0.8
V
55
90 135 μA
-10
0
10
μA
- 3dB BW
-3dB Bandwidth
A_V = 1, R_F = 200Ω, V_OUT = 400MV_P-P, C_L = 5.5pF,
C_G = 0.6pF
A_V = 2, R_F = R_G = 453Ω, V_OUT = 2V_P-P, C_L = 5.5pF,
C_G = 0.6pF
420
MHz
165
MHz
3
FN7459.2
July 3, 2012