ISL22419 Datasheet, PDF (3/13 Pages) Intersil Corporation – Low Noise, Low Power, SPI Bus, 128 Taps, Wiper Only

ISL22419
Absolute Maximum Ratings
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage at any Digital Interface Pin
with Respect to GND . . . . . . . . . . . . . . . . . . . . -0.3V to V_CC + 0.3
V_CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6V
Voltage at any DCP pin with Respect to GND . . . . . . . -0.3V to V_CC
I_W (10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA
Latchup (Note 2) . . . . . . . . . . . . . . . . . . Class II, Level B @+125°C
ESD Rating
HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5kV
CDM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1kV
Thermal Information
Thermal Resistance (Typical, Note 1)
θ_JA (°C/W)
8 Lead MSOP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
165
Maximum Junction Temperature (Plastic Package). . . . . . . .+150°C
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Recommended Operating Conditions
Ambient Temperature . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C
V_CC Voltage for DCP Operation . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
Wiper Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -3mA to 3mA
Power Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5mW
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
1. θ_JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
2. Jedec Class II pulse conditions and failure criterion used. Level B exceptions are: using a max positive pulse of 6.5V on the SHDN pin, and using
a max negative pulse of -1V for all pins.
Analog Specifications
Over recommended operating conditions unless otherwise stated. Parameters with MIN and/or MAX limits are
100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not
production tested.
SYMBOL
PARAMETER
TEST CONDITIONS
TYP
MIN (Note 3) MAX
UNIT
R_TOTAL End-to-End Resistance
W option
U option
10
kΩ
50
kΩ
End-to-End Resistance Tolerance
-20
+20
%
End-to-End Temperature Coefficient W option
±50
ppm/°C
(Note 11)
U option
±80
ppm/°C
(Note 11)
R_W
(Note 11)
C_W
(Note 11)
Wiper Resistance
Wiper Capacitance
V_CC = 3.3V @ +25°C,
wiper current = V_CC/R_TOTAL
70
Ω
25
pF
I_LkgRW Leakage on RW Pin
Voltage at pin from GND to V_CC
VOLTAGE DIVIDER MODE ( measured at R_W, unloaded)
INL
(Note 7)
Integral Non-linearity
2
4
µA
-1
1
LSB
(Note 4)
DNL
Differential Non-linearity
Monotonic over all tap positions
-0.5
(Note 6)
0.5
LSB
(Note 4)
ZSerror
(Note 5)
Zero-scale Error
W option
0
1
5
LSB
(Note 4)
U option
0
0.5
2
LSB
(Note 4)
FSerror
(Note 6)
Full-scale Error
W option
-5
-1
0
LSB
(Note 4)
U option
-2
-1
0
LSB
(Note 4)
TC_V
Ratiometric Temperature Coefficient DCP register set to 40 hex
(Notes 8, 11)
±4
ppm/°C
3
FN6311.1
September 8, 2009