English
Language : 

FN6579 Datasheet, PDF (3/14 Pages) Intersil Corporation – Negative Signal Swing, Sub-ohm, Dual SPDT Single Supply Switch
◁
ISL54059
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to 7.0V
Input Voltages
NOx, NCx (Note 5) . . . . . . . . . . . . . . . . (V+ - 7V) to ((V+) + 0.5V)
INx (Note 5) . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to ((V+) + 0.5V)
Output Voltages
COMx (Note 5) . . . . . . . . . . . . . . . . . . . (V+ - 7V) to ((V+) + 0.5V)
Continuous Current NOx, NCx, or COMx. . . . . . . . . . . . . ±300mA
Peak Current NOx, NCx, or COMx
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . ±500mA
ESD Rating:
Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>6kV
Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>400V
Charged Device Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . >1.5kV
Thermal Information
Thermal Resistance (Typical)
θJA (°C/W) θJC (°C/W)
10 Ld 3x3 TDFN Package (Notes 6, 8)
52
18
10 Ld µTQFN Package (Note 7) . . . . . 154
N/A
Maximum Junction Temperature (Plastic Package). . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
Power Supply Range . . . . . . . . . . . . . . . . . . . . . . . . +1.8V to +6.5V
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
5. Signals on NC, NO, IN, or COM exceeding V+ or GND by specified amount are clamped by internal diodes. Limit forward diode current to
maximum current ratings.
6. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379.
7. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
8. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications - 5V Supply Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 9), Unless
Otherwise Specified.
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Notes 10, 11) TYP (Notes 10, 11) UNITS
ANALOG SWITCH CHARACTERISTICS
ON-Resistance, rON
V+ = 4.5V, ICOM = 100mA, VNO or VNC = (V+ - 6.5) 25
-
0.52
-
Ω
to V+ (see Figure 5)
Full
-
0.68
-
Ω
rON Matching Between Channels, V+ = 4.5V, ICOM = 100mA, VNO or VNC = Voltage at 25
-
10
-
mΩ
ΔrON
max rON, (Note 13)
Full
-
13.1
-
mΩ
rON Flatness, RFLAT(ON)
V+ = 4.5V, ICOM = 100mA, VNO or VNC = (V+ - 6.5) 25
-
0.11
-
Ω
to V+, (Note 12)
Full
-
0.14
-
Ω
NO or NC OFF Leakage Current, V+ = 5V, VCOM = -1.5V, 5V, VNO or VNC = 5V, -1.5V 25
INO(OFF) or INC(OFF)
Full
COM ON Leakage Current,
ICOM(ON)
V+ = 5V, VCOM = -1.5V, 5V, VNO or VNC = Float
25
Full
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
V+ = 4.5V, VNO or VNC = 3.0V, RL = 50Ω,
25
CL = 35pF (see Figure 1)
Full
Turn-OFF Time, tOFF
V+ = 4.5V, VNO or VNC = 3.0V, RL = 50Ω,
25
CL = 35pF (see Figure 1)
Full
Break-Before-Make Time Delay, tD V+ = 5.5V, VNO or VNC = 3.0V, RL = 50Ω,
Full
CL = 35pF (see Figure 3)
Charge Injection, Q
VG = 0V, RG = 0Ω, CL = 1.0nF (see Figure 2)
25
OFF-Isolation
RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS 25
(see Figure 4)
Crosstalk (Channel-to-Channel) RL = 50Ω, CL = 5pF, f = 1MHz, VCOM = 1VRMS
25
(see Figure 6)
Total Harmonic Distortion
-3dB Bandwidth
f = 20Hz to 20kHz, VCOM = 0.5VP-P, RL = 32Ω
25
VCOM = 1VRMS, RL = 50Ω, CL = 5pF
25
-
-8.13
-
-
-0.4
-
-
-4.42
-
-
-0.33
-
-
35
-
-
50
-
-
16
-
-
22
-
-
18
-
-
170
-
-
60
-
-
-75
-
-
0.02
-
-
60
-
nA
µA
nA
µA
ns
ns
ns
ns
ns
pC
dB
dB
%
MHz
3
FN6579.2
March 11, 2011
 ▷