DG201A_01 Datasheet, PDF (2/7 Pages) Intersil Corporation – Quad SPST, CMOS Analog Switches

DG201A, DG202
Absolute Maximum Ratings
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44V
V- to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25V
V_IN to Ground (Note 1) . . . . . . . . . . . . . . . . . . . (V-) -2V to (V+) +2V
V_S or V_D to V+ (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . +2 to (V-) -2V
V_S or V_D to V- (Note 1) . . . . . . . . . . . . . . . . . . . . . . . -2 to (V+) +2V
Current, any Terminal Except S or D . . . . . . . . . . . . . . . . . . . . 30mA
Continuous Current, S or D . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . . . . 70mA
Operating Conditions
Temperature Range
“A” Suffix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55^oC to 125^oC
“B” Suffix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25^oC to 85^oC
“C” Suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0^oC to 70^oC
Thermal Information
Thermal Resistance (Typical, Note 2)
θ_JA (^oC/W) θ_JC (^oC/W)
CERDIP Package. . . . . . . . . . . . . . . . .
75
20
PDIP Package . . . . . . . . . . . . . . . . . . . 100
N/A
SOIC Package . . . . . . . . . . . . . . . . . . . 100
N/A
Maximum Junction Temperature
Ceramic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175^oC
Plastic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150^oC
Maximum Storage Temperature Range . . . . . . . . . . -65^oC to 150^oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300^oC
(SOIC - Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Signals on V_S, V_D, or V_IN exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings.
2. θ_JA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
V+ = 15V, V- = -15V, GND = 0V, T_A = 25^oC
“A” SUFFIX
“B” AND “C” SUFFIX
PARAMETER
DYNAMIC CHARACTERISTICS
TEST CONDITIONS
(NOTE 3)
(NOTE 3)
MIN TYP MAX MIN TYP MAX UNITS
Turn-ON Time, t_ON
Turn-OFF Time, t_OFF
See Figure 1
See Figure 1
-
480
600 -
480
-
ns
-
370
450 -
370
-
ns
Charge Injection, Q
OFF Isolation, OIRR
Crosstalk (Channel to Channel), CCRR
C_L = 1nF, R_S = 0, V_S = 0V
V_IN = 5V, R_L = 75Ω, V_S = 2.0V,
f = 100kHz
-
20
-
-
20
-
pC
-
70
-
-
70
-
dB
-
-90
-
-
-90
-
dB
Source OFF Capacitance, C_S(OFF)
f = 140kHz, V_IN = 5V, V_S = V_D = 0V -
5.0
-
-
5.0
-
pF
Drain OFF Capacitance, C_D(OFF)
-
5.0
-
-
5.0
-
pF
Channel ON Capacitance,
C_D(ON) + C_S(ON)
-
16
-
-
16
-
pF
DIGITAL INPUT CHARACTERISTICS
Input Current with Voltage High, I_IH
Input Current with Voltage Low, I_IL
V_IN = 2.4V
V_IN = 15V
V_IN = 0V
-1.0 -0.0004 - -1.0 -0.0004 -
µA
-
0.003 1.0 -
0.003 1.0 µA
-1.0 -0.0004 - -1.0 -0.0004 -
µA
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
-15
-
15 -15
-
15
V
Drain-Source ON Resistance, r_DS(ON)
V_D = ±10V, V_IN = 0.8V (DG201A)
-
115
175 -
115
200
Ω
I_S = 1mA, V_IN = 2.4V (DG202)
Source OFF Leakage Current, I_S(OFF)
V_IN = 2.4V V_S = 14V, V_D = -14V
-
0.01
1.0 -
0.01
5.0 nA
(DG201A)
V_IN = 0.8V ^{VS = -14V, VD = 14V -1.0}
-0.02
- -5.0 -0.02
-
nA
Drain OFF Leakage Current, I_D(OFF)
(DG202) _{VS = -14V, VD = 14V}
-
0.01
1.0 -
0.01
5.0 nA
V_S = 14V, V_D = -14V -1.0 -0.02
- -5.0 -0.02
-
nA
2