DG406_14 Datasheet, PDF (15/15 Pages) Intersil Corporation – Single 16-Channel/Differential 8-Channel, CMOS Analog Multiplexers

DG406, DG407
Small Outline Plastic Packages (SOIC)
N
INDEX
AREA
H
E
-B-
0.25(0.010) M B M
123
-A-
D
SEATING PLANE
A
L
h x 45o
-C-
a
e
A1
C
B
0.10(0.004)
0.25(0.010) M C A M B S
TYPICAL RECOMMENDED LAND PATTERN
(1.50mm)
(9.38mm)
(1.27mm TYP)
(0.51mm TYP)
M28.3 (JEDEC MS-013-AE ISSUE C)
28 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE
INCHES
MILLIMETERS
SYMBOL MIN
MAX
MIN
MAX NOTES
A
0.0926 0.1043 2.35
2.65
-
A1
0.0040 0.0118 0.10
0.30
-
B
0.013 0.0200 0.33
0.51
9
C
0.0091 0.0125 0.23
0.32
-
D
0.6969 0.7125 17.70 18.10
3
E
0.2914 0.2992 7.40
7.60
4
e
0.05 BSC
1.27 BSC
-
H
0.394 0.419 10.00 10.65
-
h
0.01
0.029 0.25
0.75
5
L
0.016 0.050 0.40
1.27
6
N
28
28
7
α
0^o
8^o
0^o
8^o
-
Rev. 1, 1/13
NOTES:
1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
Publication Number 95.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
4. Dimension “E” does not include interlead flash or protrusions. Interlead
flash and protrusions shall not exceed 0.25mm (0.010 inch) per side.
5. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above
the seating plane, shall not exceed a maximum value of 0.61mm
(0.024 inch)
10. Controlling dimension: MILLIMETER. Converted inch dimensions are
not necessarily exact.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
15
FN3116.11
October 1, 2013