ISL6268 Datasheet, PDF (12/14 Pages) Intersil Corporation – High-Performance Notebook PWM Controller

ISL6268
MOSFET Selection and Considerations
Typically, a MOSFET cannot tolerate even brief excursions
beyond their maximum drain to source voltage rating. The
MOSFETs used in the power stage of the converter should
have a maximum V_DS rating that exceeds the sum of the
upper voltage tolerance of the input power source and the
voltage spike that occurs when the MOSFET switches off.
There are several power MOSFETs readily available that are
optimized for DC/DC converter applications. The preferred
high-side MOSFET emphasizes low switch charge so that
the device spends the least amount of time dissipating
power in the linear region. Unlike the low-side MOSFET
which has the drain-source voltage clamped by its body
diode during turn off, the high-side MOSFET turns off with
V_IN - V_OUT - V_L across it. The preferred low-side MOSFET
emphasizes low r _DS(on) when fully saturated to minimize
conduction loss.
For the low-side MOSFET, (LS), the power loss can be
assumed to be conductive only and is written as:
P_{CON_LS} ≈ I_LOAD2 ⋅ r_{DS(on)_LS} • (1 – D)
(EQ. 16)
For the high-side MOSFET, (HS), its conduction loss is
written as:
P_{CON_HS} = I_LOAD2 • r_{DS(on)_HS} • D
(EQ. 17)
For the high-side MOSFET, its switching loss is written as:
P_{SW_HS}
=
-^V----^I--^N----^•---^I--^V----^A----^L---^L---^E----^Y-----^•--^T----^O-----^N----^•---^F----^S----^W--- + ^V-----^I--^N----^•---^I--^P----^E----^A----^K----^•---^T----^O----^F----^F----^•---^F---^S----^W----
2
2
(EQ. 18)
where:
- I_VALLEY is the difference of the DC component of the
inductor current minus half of the inductor ripple current
- I_PEAK is the sum of the DC component of the inductor
current plus half of the inductor ripple current
- T_ON is the time required to drive the device into saturation
- T_OFF is the time required to drive the device into cut-off
Selecting The Bootstrap Capacitor
The selection of the bootstrap capacitor is written as:
C_BOOT
=
---------^Q-----^g---------
∆V_BOOT
(EQ. 19)
where:
- Q_g is the total gate charge required to turn on the
high-side MOSFET
- ∆V_BOOT, is the maximum allowed voltage decay across
the boot capacitor each time the high-side MOSFET is
switched on
As an example, suppose the high-side MOSFET has a total
gate charge Q_g of 25nC at V_GS = 5V, and a ∆V_BOOT of
200mV. The calculated bootstrap capacitance is 0.125µF.
For a comfortable margin, select a capacitor that is double
the calculated capacitance; in this example, 0.22µF will
suffice. Use an X7R or X5R ceramic capacitor.
Layout Considerations
As a general rule, power should be on the bottom layer of
the PCB and weak analog or logic signals are on the top
layer of the PCB. The ground-plane layer should be adjacent
to the top layer to provide shielding. The ground plane layer
should have an island located under the IC, the
compensation components, and the FSET components. The
island should be connected to the rest of the ground plane
layer at one point.
VIAS TO
GROUND
PLANE
INDUCTOR
HIGH-SIDE
MOSFETS
GND
VOUT
OUTPUT
CAPACITORS
SCHOTTKY
DIODE
PHASE
NODE
LOW-SIDE
MOSFETS
INPUT
VIN
CAPACITORS
FIGURE 7. TYPICAL POWER COMPONENT PLACEMENT
Signal Ground and Power Ground
The GND pin is the signal ground for analog and logic
signals of the IC. For a robust thermal and electrical
conduction path, connect the GND pin to the island of
ground plane under the top layer using several vias.
Connect the input capacitors, the output capacitors, and the
source of the lower MOSFETs to the power ground plane.
PGND (Pin 12)
This is the return path for the pull-down of the LG low-side
MOSFET gate driver. Ideally, PGND should be connected to
the source of the low-side MOSFET with a low-resistance,
low-inductance path.
VIN (Pin 3)
The VIN pin should be connected close to the drain of the
high-side MOSFET, using a low resistance and low
inductance path.
VCC (Pin 4)
For best performance, place the decoupling capacitor very
close to the VCC and GND pins.
PVCC (Pin 14)
For best performance, place the decoupling capacitor very
close to the PVCC and PGND pins, preferably on the same
side of the PCB as the ISL6268 IC.
12
FN6348.0
August 22, 2006