ISL6218_14 Datasheet, PDF (12/19 Pages) Intersil Corporation – Precision Single-Phase Buck PWM Controller for Intel Mobile Voltage Positioning IMVP-IV and IMVP-IV+

ISL6218
shutting off the low side MOSFET. This “Three-State” mode
will hold both upper and low side MOSFETs off during the
time that the Low Side MOSFET would normally be on.
This “Diode Emulation” is initiated when the current, as
sensed through the low side MOSFET, is negative. This event
triggers the “Three-State” mode until the next PWM cycle.
This Discontinuous operation improves efficiency by preventing
the reverse conduction of current through the low side
MOSFET. This eliminates conduction loss and output
discharge. Discontinuous operation is enabled in Deep and
Deeper Sleep modes and is based solely on current feedback.
Due to this ISL6218’s ability to sense zero current and
prevent discharging through the low side MOSFETs during
light loads, the ISL6218 meets the requirements for PSI
without requiring any external signals.
STV, DSV and DRSV
START-UP “BOOT” VOLTAGE - STV
The Start-up, or “Boot,” voltage is programmed by an
external resistor divider network from the OCSET pin (refer
to Figure 8). Internally, a 1.75V reference voltage is output
on the OCSET pin. The start-up voltage is set through a
voltage divider from the 1.75V reference at the OCSET pin.
The voltage on the STV pin will be the controller regulating
voltage during the start-up sequence.
Once the PGOOD pin of the ISL6218 controller is externally
enabled high by the Vccp and Vcc_mch controllers, the
ISL6218 will then ramp, after a 10µs delay, to the voltage
commanded by the VID setting minus “Droop”.
DEEP SLEEP VOLTAGE- DSV
The Deep Sleep voltage is programmed by an external
voltage divider network from the DACOUT pin (Refer to
Figure 8). The DACOUT pin is the output of the VID digital-
to-analog converter. By having the Deep Sleep voltage setup
from a resistor divider from DAC, the Deep Sleep voltage will
be a constant percentage of the VID. Through the voltage
divider network, Deep Sleep voltage is set to 98.8% of the
programmed VID voltage, as per the IMVP-IV^™ specification.
The IC enters the Deep Sleep mode when the DSEN is low
and the DRSEN pin is low as shown in Figure 6 and
Figure 5. Once in Deep Sleep Mode, the controller will
regulate to the voltage seen on the DSV pin minus “Droop”.
DEEPER SLEEP VOLTAGE - DRSV
The Deeper Sleep voltage, DRSV, is programmed by an
external voltage divider network from the 1.75V reference on
the OCSET pin (Refer to Figure 8). In Deeper Sleep mode
the ISL6218 controller will regulate the output voltage to the
voltage present on the DRSV pin minus “Droop”.
The IC enters Deeper Sleep mode when DRSEN is high and
DSEN is low, as shown in Figure 5.
BATTERY
V _REF = 1.75V
I _OCSET
ISL6218
OCSET
R1 _36.5k
VBAT
1.200V _STV
R2 30.1k
VID COMMAND
DACOUT
VOLTAGE
0.750V _DRSV
1.21k
R3 49.9k
SOFT
GND
DSV
98.8%
DACOUT
0.012µF
98.8k
FIGURE 8. CONFIGURATIONS FOR BATTERY INPUT,
OVERCURRENT SETTING AND START, DEEP
SLEEP AND DEEPER SLEEP VOLTAGE
OVERCURRENT SETTING - OCSET
The ISL6218 overcurrent protection essentially compares a
user-selectable overcurrent threshold to the scaled and
sampled output current. An overcurrent condition is defined
when the sampled current is equal to or greater than the
threshold current. A step by step process to the user-desired
overcurrent set point is detailed next.
Step 1: Setting the Overcurrent Threshold
The overcurrent threshold is represented by the DC current
flowing out of the OCSET pin (See Figure 8). Since the
OCSET pin is held at a constant 1.75V, the user need only
populate a resistor from this pin to ground to set the desired
overcurrent threshold, I_OCSET. The user should pick a value
of I_OCSET between 10µA and 15µA. Once this is done, use
Ohm’s Law to determine the necessary resistor to place from
OCSET to ground:
R_OCSET
=
1.75V
I_OCSET
= R₁ + R₂
+ R₃
(EQ. 2)
For example, if the desired overcurrent threshold is 15µA,
the total resistance from OCSET must equal 117kΩ.
Step 2: Selecting ISEN Resistance for Desired
Overcurrent Level
After choosing the I_OCSET level, the user must then decide
what level of total output current is desired for overcurrent.
Typically, this number is between 150% and 200% of the
maximum operating current of the application. For example,
if the max operating current is 27A, and the user chooses
150% overcurrent, the ISL6218 will shut down if the output
current exceeds 27A*1.5 or 40A. According to the “Block
Diagram” on page 7, Equation 3 should be used to
determine R_ISEN once the overcurrent level, I_OC, is chosen.
12
FN9101.6
August 6, 2007