ISL29147_15 Datasheet, PDF (10/15 Pages) Intersil Corporation – Low Power Ambient Light and Proximity Sensor with Enhanced Infrared Rejection

ISL29147
Registers 0x01 and 0x02 are used to configure the primary
proximity and ALS parameters. Register 0x03 is used for optimizing
IR compensation in ALS measurements. A procedure to optimize IR
compensation is described in “ALS IR Compensation” on page 11.
Register 0x04 is the Interrupt Configuration and Status Register,
they are used primarily to indicate interrupt events from proximity
and ALS measurements. A PWR_FAIL bit to indicate a ‘Brown-Out’
event is available and is set in case of a power supply interruption. A
‘Brown-Out’ event does not generate a hardware interrupt. The host
microcontroller must clear this bit by writing a ‘0’ to Reg 0x04[4].
Register 0x04 is also used to configure ALS and Proximity
interrupt persistency and the operation of the INT pin.
Registers 0x05 and 0x06 are used to set the proximity ‘LOW’ and
‘HIGH’ threshold for proximity interrupt event generation.
Registers 0x07, 0x08 and 0x09 are used to set the ALS ‘LOW’
and ‘HIGH’ threshold. Two 12-bit numbers span three address
locations as shown in Table 1.
Data registers 0x0A holds result of proximity conversion. The
proximity result should be validated by ‘Washout’ bit in
Reg 0x0D[0]. Registers 0x0B and 0x0C holds result of an ALS
measurement.
The ALS data is 12 bits wide. Least Significant Byte of the ALS
data is available at address 0x0C and Most Significant Byte
(MSB) of ALS data is available at address 0x0B. The MSB is right
justified, i.e., the upper nibble is always zero and lower nibble
contains four data bits.
Register 0x0D[7:1] contains ambient IR measurement in proximity
measurement phase. This measurement is for detecting ambient
Wash out condition, which is indicated by Reg 0x0D[0] being ‘HIGH’.
Proximity ‘Washout’ is described in “Proximity Ambient Washout
Detection” on page 11.
A software reset can be initiated by writing 0x38 to Register
0x0E.
ISL29147 Operation
Photodiodes and ADCs
The ISL29147 contains two photodiode arrays, which convert
photons (light) into current. The ALS photodiodes are designed to
mimic the human eye’s wavelength response curve to visible light.
The ALS photodiodes’ current output is digitized by a 12-bit ADC.
The ALS ADC output is accessed by reading from Reg 0x0B and
0x0C when the ADC conversion is completed.
The ALS ADC converter uses a charge-balancing architecture.
Charge-balancing is best suited for converting small current signals
in the presence of periodic AC noise. The ISL29147 targets an
integration time of 90ms, which can vary ±15% from nominal. The
ALS integration time is intended to minimize 60Hz flicker.
The proximity sensor uses an 8-bit ADC, which operates in a
similar fashion. The IRDR pin drives (pulses) an infrared LED, the
emitted IR reflects off an object back into the ISL29147, and the
photo diodes convert the reflected IR to a current signal in
0.5ms. The ADC subtracts the IR reading before and after the
LED is driven to remove ambient IR contribution.
The ALS runs continuously with new data available every 90ms.
The proximity sensor runs continuously with a time between
conversions controlled by PROX_SLP (Reg 0x01[6:4]).
Ambient Light Sensing
The ISL29147 is set for ambient light sensing when Register bit
ALS_EN = 1. Four measurement ranges from 56.25 Lux to 1800 Lux
are available. The ALS measurement range is configured via
Reg 0x02[1:0].
Proximity Sensing
When proximity sensing is enabled (PROX_EN = 1), the external
IR LED is driven for 90µs by the built-in IR LED driver through the
IRDR pin.
ALS CONVERSION TIME =
90ms (FIXED)
SEVERAL µs BETWEEN
CONVERSIONS
ALS
ACTIVE
90ms
PROX
SENSOR
ACTIVE
90ms
90ms
90ms
0.50ms FOR PROX
CONVERSION
90ms
TIME
TIME
IRDR
(CURRENT
DRIVER)
SERIES OF
CURRENT PULSES
TOTALING 0.09ms
TIME
SLEEP TIME
(PROX_SLP)
FIGURE 9. TIMING DIAGRAM FOR PROX/ALS EVENTS - NOT TO SCALE
The IR LED current depends on PROX_DRV (Reg 0x01[1:0]). Drive
current settings are as shown in Table 1. The IR LED drive is in
high impedance state when not active.
When the IR from the LED reaches an object and gets reflected
back to the ISL29147, the reflected IR light is converted into a
current. This current is converted to digital data using an 8-bit
ADC. The proximity measurement takes 0.5ms for one
conversion including the 90μs LED drive time. The period
between proximity measurements is determined by PROX_SLP
(sleep time) in Reg 0x01[4:2].
Average LED driving current consumption is given by Equation 1.
I_lRDR;AVE = ^I--^l--^R----^D----^R----_T-^;-^P--_S--^E--_L--^A-_E---^K-_E----_P^-----⁹---⁰----^----^s-
(EQ. 1)
A typical IRDR scheme is 250mA pulses every 400ms, averaging
about 56μA DC.
Submit Document Feedback ₁₀
FN8409.3
January 6, 2015