ISL72026SEH Datasheet, PDF (1/18 Pages) Intersil Corporation – 3.3V Radiation Tolerant CAN Transceiver, 1Mbps, Listen Mode, Loopback

DATASHEET
3.3V Radiation Tolerant CAN Transceiver, 1Mbps, Listen
Mode, Loopback
ISL72026SEH
The Intersil ISL72026SEH is a radiation tolerant 3.3V CAN
transceiver that is compatible with the ISO11898-2 standard
for applications calling for Controller Area Network (CAN) serial
communication in satellites and aerospace communications
and telemetry data processing in harsh industrial
environments.
The transceiver can transmit and receive at bus speeds of up to
1Mbps. The device is designed to operate over a common mode
range of -7V to +12V with a maximum of 120 nodes. The device
has three discrete selectable driver rise/fall time options, a
listen mode feature and loopback test capability.
Receiver (Rx) inputs feature a “full fail-safe” design, which
ensures a logic high Rx output if the Rx inputs are floating,
shorted, or terminated but undriven.
The ISL72026SEH is available in an 8 Ld hermetic ceramic
flatpack and die form that operate across the temperature
range of -55°C to +125°C. The logic inputs are tolerant with
5V systems.
Other CAN transceivers available are the ISL72027SEH and
ISL72028SEH. For a list of differences see Table 1 on page 2.
Related Literature
• UG051, “ISL7202xSEHEVAL1Z Evaluation Board User Guide”
• TR018, “SEE Testing of the ISL72027SEH CAN Transceiver”
• TR022, “Total Dose Testing of the ISL72026SEH,
ISL72027SEH and ISL72028SEH CAN Transceivers”
Features
• Electrically screened to SMD 5962-15228
• ESD protection on all pins. . . . . . . . . . . . . . . . . . . . . . 4kV HBM
• Compatible with ISO11898-2
• Operating supply range . . . . . . . . . . . . . . . . . . . . . 3.0V to 3.6V
• Bus pin fault protection to ±20V
• Undervoltage lockout
• Cold spare: powered down devices/nodes will not affect
active devices operating in parallel
• Three selectable driver rise and fall times
• Glitch free bus I/O during power-up and power-down
• Full fail-safe (open, short, terminated/undriven) receiver
• Hi Z input allows for 120 nodes on the bus
• High data rates. . . . . . . . . . . . . . . . . . . . . . . . . . . up to 1Mbps
• Quiescent supply current . . . . . . . . . . . . . . . . . . . . 7mA (max)
• Listen mode supply current . . . . . . . . . . . . . . . . . . 2mA (max)
• -7V to +12V common mode input voltage range
• 5V tolerant logic inputs
• Thermal shutdown
• Acceptance tested to 75krad(Si) (LDR) wafer-by-wafer
• Radiation tolerance
- SEL/B immune to LET 60MeV•cm²/mg
- Low dose rate (0.01rad(Si)/s) . . . . . . . . . . . . . . 75krad(Si)
Applications
• Satellites and aerospace communications
• Telemetry data processing
• High-end industrial environments
• Harsh environments
Tx DATA IN
VCC
0.1µF
1D
RS ₈
2 GND
CANH ₇
ISL72026SEH
3 _VCC
CANL ₆
4R
LBK ₅
CANH
CANL
µController
Rx DATA OUT
FIGURE 1. TYPICAL APPLICATION
4
D
0
4
0
R
3
RS = GND, R_D = 60Ω
2
1
CANH - CANL
0
TIME (1µs/DIV)
FIGURE 2. FAST DRIVER AND RECEIVER WAVEFORMS
November 9, 2015
1
FN8762.1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2015. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.