7028L15PFG8 Datasheet, PDF (3/17 Pages) Integrated Device Technology – True Dual-Ported memory cells which allow simultaneous reads of the same memory location

IDT7028L
High-Speed 64K x 16 Dual-Port Static RAM
Pin Names
Left Port
Right Port
Names
Industrial and Commercial Temperature Ranges
CE0L, CE1L
R/WL
CE0R, CE1R
R/WR
Chip Enables
Read/Write Enable
OEL
OER
Output Enable
A0L - A15L
A0R - A15R
Address
I/O0L - I/O15L
I/O0R - I/O15R
Data Input/Output
SEML
SEMR
Semaphore Enable
UBL
UBR
Upper Byte Select
LBL
LBR
Lower Byte Select
INTL
INTR
Interrupt Flag
BUSYL
BUSYR
M/S
Busy Flag
Master or Slave Select
VCC
Power
GND
Ground
4836 tbl 01
Absolute Maximum Ratings⁽¹⁾
Symbol
Rating
Commercial Military Unit
& Industrial
VTERM⁽²⁾
Terminal Voltage
with Respect
to GND
-0.5 to +7.0 -0.5 to +7.0 V
TBIAS
Temperature
Under Bias
-55 to +125 -65 to +135 ^oC
TSTG
Storage
Temperature
-65 to +150 -65 to +150 ^oC
IOUT
DC Output Current
50
50
mA
NOTES:
4836 tbl 02
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may
cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any other conditions above those
indicated in the operational sections of this specification is not implied. Exposure
to absolute maximum rating conditions for extended periods may affect
reliability.
2. VTERM must not exceed Vcc + 10% for more than 25% of the cycle time or 10ns
maximum, and is limited to < 20mA for the period of VTERM > Vcc + 10%.
Recommended DC Operating
Conditions
Symbol
Parameter
Min. Typ. Max. Unit
VCC Supply Voltage
4.5 5.0 5.5 V
GND Ground
0
0
0
V
VIH Input High Voltage
2.2
____
6.0⁽²⁾
V
VIL Input Low Voltage
-0.5⁽¹⁾
____
0.8
V
NOTES:
1. VIL > -1.5V for pulse width less than 10ns.
2. VTERM must not exceed Vcc + 10%.
4836 tbl 04
Capacitance
(TA = +25°C, f = 1.0MHz)
Symbol
Parameter⁽¹⁾
Conditions⁽²⁾
Max. Unit
Maximum Operating Temperature
and Supply Voltage
Ambient
Grade
Temperature⁽¹⁾
GND
Vcc
Military
-55^OC to +125^OC
0V
5.0V + 10%
Commercial
0^OC to +70^OC
0V
5.0V + 10%
CIN Input Capacitance
VIN = 3dV
9 pF
COUT Output Capacitance
VOUT = 3dV
10 pF
NOTES:
4836 tbl 05
1. This parameter is determined by device characterization but is not production
tested.
2. 3dV represents the interpolated capacitance when the input and output signals
switch from 0V to 3V or from 3V to 0V.
Industrial
-40^OC to +85^OC
0V
5.0V + 10%
NOTES:
4836 tbl 03
1. This is the parameter TA. This is the "instant on" case temperature.
6.342