ICS9148-32 Datasheet, PDF (10/14 Pages) Integrated Circuit Systems – Pentium/ProTM System Clock Chip

ICS9148-32
Absolute Maximum Ratings
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0V
Logic Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND –0.5 V to V_DD +0.5 V
Ambient Operating Temperature . . . . . . . . . . . . 0°C to +70°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are
stress specifications only and functional operation of the device at these or any other conditions above those listed in the
operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods
may affect product reliability.
Electrical Characteristics - Input/Supply/Common Output Parameters
T_A = 0 - 70C; Supply Voltage V_DD = V_DDL = 3.3 V +/-5% (unless otherwise stated)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX UNITS
Input High Voltage
Input Low Voltage
Input High Current
Input Low Current
Input Low Current
Operating
Supply Current
Power Down
Supply Current
V_IH
2
V_DD+0.3 V
V_IL
V_SS-0.3
0.8
V
I_IH
V_IN = V_DD
0.1
5
µA
I_IL1
V_IN = 0 V; Inputs with no pull-up resistors
-5
2.0
µA
I_IL2
V_IN = 0 V; Inputs with pull-up resistors
-200 -100
µA
I_DD3.3OP66 C_L = 0 pF; Select @ 66MHz
60 170 mA
I_DD3.3OP100 C_L = 0 pF; Select @ 100MHz
66 170
I_DD3.3PD C_L = 0 pF; With input address to Vdd or GND
3
650 µA
Input frequency
Input Capacitance¹
Transition Time¹
Settling Time¹
Clk Stabilization¹
Skew¹
F_i
C_IN
C_INX
T_trans
T_s
T_STAB
T_AGP-PCI1
V_DD = 3.3 V;
Logic Inputs
X1 & X2 pins
To 1st crossing of target Freq.
From 1st crossing to 1% target Freq.
From V_DD = 3.3 V to 1% target Freq.
V_T = 1.5 V;
14.318
5
27
36
45
3
5
3
1
3.5
4
MHz
pF
pF
ms
ms
ms
ns
1_{Guaranteed by design, not 100% tested in production.}
Electrical Characteristics - Input/Supply/Common Output Parameters
TA = 0 - 70C; Supply Voltage VDD = 3.3 V +/-5%, VDDL = 2.5 V +/-5% (unless otherwise stated)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX
Operating
IDD2.5OP66 CL = 0 pF; Select @ 66.8 MHz
16
72
Supply Current
IDD2.5OP100 CL = 0 pF; Select @ 100 MHz
23 100
Power Down Supply
Current
I_DD2.5PD
C_L = 0 pF; With input address to
Vdd or GND
10 100
Skew¹
tCP U -A GP
tCP U -P CI2
VT = 1.5 V; VTL = 1.25 V
0
0.5
1
1
2.6
4
1_{Guaranteed by design, not 100% tested in production.}
UNITS
mA
mA
µA
ns
ns
10