IC80C51 Datasheet, PDF (11/44 Pages) Integrated Circuit Solution Inc – CMOS SINGLE CHIP 8-BIT MICROCONTROLLER

IC80C51
IC80C31
The detail description of each bit is as follows:
PSW:
Program Status Word. Bit Addressable.
765
4
3
2
CY AC F0 RS1 RS0 OV
10
—P
Register Description:
CY PSW.7 Carry flag.
AC PSW.6 Auxiliary carry flag.
F0 PSW.5 Flag 0 available to the user for
general purpose.
RS1 PSW.4 Register bank selector bit 1.⁽¹⁾
RS0 PSW.3 Register bank selector bit 0.⁽¹⁾
OV PSW.2 Overflow flag.
— PSW.1 Usable as a general purpose flag
P PSW.0 Parity flag. Set/Clear by hardware each
instruction cycle to indicate an odd/even
number of “1” bits in the accumulator.
Note:
1. The value presented by RS0 and RS1 selects the corre-
sponding register bank.
RS1 RS0 Register Bank
Address
0
0
0
00H-07H
0
1
1
08H-0FH
1
0
2
10H-17H
1
1
3
18H-1FH
PCON:
Power Control Register. Not Bit Addressable.
765
4
3
2
10
SMOD — — — GF1 GF0 PD IDL
Register Description:
SMOD
Double baud rate bit. If Timer 1 is used to generate
baud rate and SMOD=1, the baud rate is doubled
when the serial port is used in modes 1, 2, or 3.
—
Not implemented, reserve for future use.⁽¹⁾
—
Not implemented, reserve for future use.⁽¹⁾
—
Not implemented, reserve for future use.⁽¹⁾
GF1
General purpose flag bit.
GF0
General purpose flag bit.
PD
Power-down bit. Setting this bit activates power-
down mode.
IDL
Idle mode bit. Setting this bit activates idle mode.
operation in the IC80C51/31. If 1s are written to
PD and IDL at the same time, PD takes precedence.
Note:
1. User software should not write 1s to reserved bits. These
bits may be used in future products to invoke new features.
IE:
Interrupt Enable Register. Bit Addressable.
765
4
3
2
10
EA — — ES ET1 EX1 ET0 EX0
Register Description:
EA IE.7
Disable all interrupts. If EA=0, no interrupt
will be acknowledged. If EA=1, each
interrupt source is individually enabled
or disabled by setting or clearing its
enable bit.
— IE.6
Not implemented, reserve for future use.
(5)
— IE.5
Not implemented, reserve for future use.
(5)
ES IE.4
Enable or disable the serial port interrupt.
ET1 IE.3
Enable or disable the Timer 1 overflow
interrupt.
EX1 IE.2
Enable or disable External Interrupt 1.
ET0 IE.1
Enable or disable the Timer 0 overflow
interrupt.
EX0 IE.0
Enable or disable External Interrupt 0.
Note: To use any of the interrupts in the 80C51 Family, the
following three steps must be taken:
1. Set the EA (enable all) bit in the IE register to 1.
2. Set the coresponding individual interrupt enable bit in
the IE register to 1.
3. Begin the interrupt service routine at the corresponding
Vector Address of that interrupt (see below).
Interrupt Source
IE0
TF0
IE1
TF1
RI & TI
Vector Address
0003H
000BH
0013H
001BH
0023H
4. In addition, for external interrupts, pins INT0 and INT1
(P3.2 and P3.3) must be set to 1, and depending on
whether the interrupt is to be level or transition activated,
bits IT0 or IT1 in the TCON register may need to be set to
0 or 1.
ITX = 0 level activated (X = 0, 1)
ITX = 1 transition activated
5. User software should not write 1s to reserved bits. These
bits may be used in future products to invoke new features.
Integrated Circuit Solution Inc.
11
MC001-0B