X25642 Datasheet, PDF (8/16 Pages) Xicor Inc. – Advanced SPI Serial E 2 PROM with Block Lock TM Protection

X25642
ABSOLUTE MAXIMUM RATINGS*
Temperature under Bias....................–65°C to +135°C
Storage Temperature ........................–65°C to +150°C
Voltage on any Pin with Respect
to V_SS .........................................................–1V to +7V
D.C. Output Current ............................................. 5mA
(Soldering, 10 seconds) ..............................300°C
RECOMMENDED OPERATING CONDITIONS
*COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and the functional operation
of the device at these or any other conditions above
those indicated in the operational sections of this
specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may
affect device reliability.
Temperature
Commercial
Industrial
Military
Min.
0°C
–40°C
–55°C
Max.
+70°C
+85°C
+125°C
7037 FRM T06
Supply Voltage
X25642
X25642-2.7
Limits
5V ±10%
2.7V to 5.5V
7037 FRM T07
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Symbol
Parameter
I_CC
I_SB
I_LI
I_LO
V_IL(1)
V_IH(1)
V_OL1
V_OH1
V_OL2
V_OH2
V_CC Supply Current (Active)
V_CC Supply Current (Standby)
Input Leakage Current
Output Leakage Current
Input LOW Voltage
Input HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
Limits
Min.
Max.
5
1
10
10
–1
V_CC x 0.3
V_CC x 0.7 V_CC + 0.5
0.4
V_CC–0.8
0.4
V_CC–0.3
Units
Test Conditions
mA SCK = V_CC x 0.1/V_CC x 0.9 @ 2MHz,
µA CS = V_CC, V_IN = V_SS or V_CC – 0.3V
µA V_IN = V_SS to V_CC
µA V_OUT = V_SS to V_CC
V
V
V I_OL = 3mA, V_CC = 5V
V I_OH = –1.6mA, V_CC = 5V
V I_OL = 1.5mA, V_CC = 3V
V I_OH = –0.4mA, V_CC = 3V
7037 FRM T08
POWER-UP TIMING
Symbol
T_PUR(3)
T_PUW(3)
Parameter
Power-up to Read Operation
Power-up to Write Operation
Min.
Max.
1
1
Units
ms
ms
7037 FRM T09
CAPACITANCE T_A = +25°C, f = 1MHz, V_CC = 5V
Symbol
Parameter
C_I/O(3)
C_IN(3)
Output Capacitance (SO)
Input Capacitance (SCK, SI, CS, WP, HOLD)
Max.
8
6
Units
pF
pF
Test Conditions
V_I/O = 0V
V_IN = 0V
7037 FRM T10
Notes: (1) V_IL min. and V_IH max. are for reference only and are not tested.
(2) This parameter is periodically sampled and not 100% tested.
(3) t_PUR and t_PUW are the delays required from the time V_CC is stable until the specified operation can be initiated. These
parameters are periodically sampled and not 100% tested.
8