FH12-33-S-0.5SH55 Datasheet, PDF (9/20 Pages) Hirose Electric – 0.5mm and 1mm Pitch Connectors For FPC/FFC

FH12 Seriesq0.5mm and 1mm Pitch Connectors For FPC/FFC
s1mm Pitch Type Bottom Contact Type
2.3
A
1.0
(0.2)
E
Mated Cross-sectional Diagram
(2.1)
FPC/FFC Contact Surface
(3.1)
(1.3)
B
C
D
4.6
5.6
Note 1 : The coplanarity of each terminal lead within specified dimension is 0.1 mm Max.
Note 2 : Packaged on tape and reel only. Check packaging specification.
Note 3 : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector.
Note 4 : After reflow, the terminal plating may change color, however this does not represent a quality issue.
Unit:mm
Part Number
CL No. Number of Contacts A
B
C
D
E
FH12-5S-1SH(**) 586-0591-6-**
5
4
8.6
9.6
6.07
2.3
FH12-6S-1SH(**) 586-0607-4-**
6
5
9.6
10.6 7.07
2.3
FH12-7S-1SH(**) 586-0535-5-**
7
6
10.6 11.6 8.07
2.3
FH12-8S-1SH(**) 586-0579-0-**
8
7
11.6 12.6 9.07
2.3
FH12-9S-1SH(**) 586-0540-5-**
9
8
12.6 13.6 10.07 2.3
FH12-11S-1SH(**) 586-0668-9-**
11
10
14.6 15.6 12.07 2.3
FH12-12S-1SH(**) 586-0741-7-**
12
11
15.6 16.6 13.07 2.3
FH12-16S-1SH(**) 586-0536-8-**
16
15
19.6 20.6 17.07 2.3
FH12-17S-1SH(**) 586-0739-5-**
17
16
20.6 21.6 18.07 2.3
FH12-22S-1SH(**) 586-0547-4-**
22
21
25.6 26.6 23.07 2.3
FH12-26S-1SH(**) 586-0592-9-**
26
25
29.6 30.6 27.07 2.3
FH12-10(4)SA-1SH(**) 586-0537-0-**
4
3
8.1
9.1
5.57
2.8
FH12-14(6)SA-1SH(**) 586-0538-3-**
6
5
10.1 11.1 7.57
2.8
FH12-18(8)SA-1SH(**) 586-0539-6-**
8
7
12.1 13.1 9.57
2.8
FH12-22(10)SA-1SH(**) 586-0541-8-**
10
9
14.1 15.1 11.57 2.8
FH12-24(11)SA-1SH(**) 586-0542-0-**
11
10
15.1 16.1 12.57 2.8
FH12-30(14)SA-1SH(**) 586-0543-3-**
14
13
18.1 19.1 15.57 2.8
FH12-40(19)SA-1SH(**) 586-0546-1-**
19
18
23.1 24.1 20.57 2.8
FH12-50(24)SA-1SH(**) 586-0548-7-**
24
23
28.1 29.1 25.57 2.8
Note 1: Embossed tape reel packaging (2,000 pieces/reel). Order by number of reels.
Note 2: The 1mm version of FH12 is constructed by loading every other contact into the 0.5mm housing.
When a housing designed for an odd number of 0.5mm pitch contacts is used; the spacing from the edge to the first contact on
either side is the same as the distance between each contact, 1.0mm. Hirose considers this design to be a standard-type 1.0mm
connector.
An eccentric-type connector using a housing designed for an even number of 0.5mm pitch contacts and consequently one side
has 1.5mm distance from the edge to the first contact. (See FPC/FFC dimensional drawing on page 19) The part number for the
eccentric type describes the size of the 0.5mm housing used and lists the number of 1.0mm pitch contacts in parentheses () as
shown in the above table.
9