|
DG201CJ Datasheet, PDF (4/8 Pages) Harris Corporation – CMOS Dual/Quad SPST Analog Switches | |||
|
◁ |
Speciï¬cations DG201
Absolute Maximum Ratings
Thermal Information
V+ to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <36V
V+ to VD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <30V
VD to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <30V
VD to VS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <28V
VREF to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <33V
VREF to VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <30V
VREF to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <20V
VIN to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <20V
Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <30mA
Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC
Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300oC
Thermal Resistance
Ceramic DIP Package . . . . . . . . . . . . . . .
Plastic DIP Package . . . . . . . . . . . . . . . .
θJA
80oC/W
145oC/W
θJC
24oC/W
-
Operating Temperature Range
âAâ Sufï¬x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to +125oC
âBâ Sufï¬x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25oC to +85oC
âCâ Sufï¬x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to +70oC
CAUTION: Stresses above those listed in âAbsolute Maximum Ratingsâ may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this speciï¬cation is not implied.
Electrical Speciï¬cations (TA = +25oC, V+ = +15V, V- = -15V)
PARAMETER
TEST CONDITIONS
MILITARY
-55oC
+25oC +125oC
COMMERCIAL / INDUSTRIAL
0oC TO
-25oC
+25oC
+70oC TO
+85oC
UNITS
Input Logic Current,
IIN(ON)
VIN = 0.8V (Note 1)
10
±1
10
±1
±1
10
µA
Input Logic Current,
IN(OFF)
VIN = 2.4V (Note 1)
10
±1
10
±1
±1
10
µA
Drain-Source On Resis- IS = 10mA, VANALOG =
80
80
125
100
100
125
â¦
tance, rDS(ON)
±10V
Channel-to-Channel
rDS(ON) Match, rDS(ON)
-
25 (Typ)
-
-
30 (Typ)
-
â¦
Minimum Analog Signal
Handling Capability,
VANALOG
-
±15 (Typ)
-
-
±15 (Typ)
-
V
Switch OFF Leakage
VANALOG = -14V to +14V
-
Current, ID(OFF)
±1
100
-
±5
100
nA
Switch OFF Leakage
VANALOG = -14V to +14V
-
Current, IS(OFF)
±1
100
-
±5
100
nA
Switch ON Leakage Cur- VD = VS = -14V to +14V
-
rent, ID(ON) + IS(ON)
±2
200
-
±5
200
nA
Switch âONâ Time
RL = 1kâ¦, VANALOG =
-
1.0
-
-
1.0
-
µs
(Note 2), tON
-10V to +10V (Figure 5)
Switch âOFFâ Time
RL = 1kâ¦, VANALOG =
-
0.5
-
-
0.5
-
µs
(Note 2), tOFF
-10V to +10V (Figure 5)
Charge Injection, Q(INJ.) Figure 6
-
15 (Typ)
-
-
20 (Typ)
-
mV
Minimum Off Isolation f = 1MHz, RL = 100â¦,
-
54 (Typ)
-
-
50 (Typ)
-
dB
Rejection Ratio, OIRR CL ⤠5pF, (Figure 7)
+Power Supply
VIN = 0V or VIN = 5V
2000
1000
2000
2000
1000
2000
µA
Quiescent Current, I+Q
-Power Supply
Quiescent Current, I-Q
2000
1000
2000
2000
1000
2000
µA
Minimum Channel to
One Channel Off
Channel Cross Coupling
Rejection Ratio, CCRR
-
54 (Typ)
-
-
50 (Typ)
-
dB
NOTES:
1. Typical values are for design aid only, not guaranteed and not subject to production testing.
2. All channels are turned off by high â1â logic inputs and all channels are turned on by low â0â inputs; however 0.8V to 2.4V describes the
minimum range for switching properly. Peak input current required for transition is typically -120µA.
9-16
|
▷ |