 English |
|
|
|
|
|
|
|
| DG201CJ Datasheet, PDF (3/8 Pages) Harris Corporation – CMOS Dual/Quad SPST Analog Switches | |||
| |||
| ◁ |
Speciï¬cations DG200
Absolute Maximum Ratings
Thermal Information
V+, V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <36V
V+ - VD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <30V
VD - V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <30V
VD - VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <28V
VIN - GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <20V
Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC
Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300oC
Thermal Resistance
Ceramic DIP Package . . . . . . . . . . . . . . .
Plastic DIP Package . . . . . . . . . . . . . . . .
Metal Can Package . . . . . . . . . . . . . . . . .
θJA
95oC/W
100oC/W
136oC/W
θJC
24oC/W
-
65oC/W
Operating Temperature Range
âAâ Sufï¬x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to +125oC
âBâ Sufï¬x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25oC to +85oC
âCâ Sufï¬x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to +70oC
CAUTION: Stresses above those listed in âAbsolute Maximum Ratingsâ may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this speciï¬cation is not implied.
Electrical Speciï¬cations (TA = +25oC, V+ = +15V, V- = -15V)
PARAMETER
TEST CONDITIONS
MILITARY
-55oC
+25oC +125oC
COMMERCIAL / INDUSTRIAL
0oC TO
-25oC
+25oC
+70oC TO
+85oC
UNITS
Input Logic Current,
VIN = 0.8V (Notes 2, 3)
±10
±1
±10
-
±10
±10
µA
IIN(ON)
Input Logic Current,
VIN = 2.4V (Notes 2, 3)
±10
±1
±10
-
±10
±10
µA
IN(OFF)
Drain-Source On Resis- IS = 10mA, VANALOG =
70
70
100
80
80
100
â¦
tance, rDS(ON)
±10V
Channel-to-Channel
rDS(ON) Match, rDS(ON)
-
25 (Typ)
-
-
30 (Typ)
-
â¦
Minimum Analog Signal
Handling Capability,
VANALOG
-
±15V
-
-
±15V
-
V
Switch OFF Leakage
VANALOG = -14V to +14V
-
Current, ID(OFF)
±2
100
-
±5
100
nA
Switch OFF Leakage
VANALOG = -14V to +14V
-
Current, IS(OFF)
±2
100
-
±5
100
nA
Switch ON Leakage Cur- VD = VS = -14V to +14V
-
rent, ID(ON) + IS(ON)
±2
200
-
±10
200
nA
Switch âONâ Time
RL = 1kâ¦, VANALOG =
-
1.0
-
-
1.0
-
µs
(Note 1), tON
-10V to +10V (Figure 5)
Switch âOFFâ Time, tOFF RL = 1kâ¦, VANALOG =
-
0.5
-
-
0.5
-
µs
-10V to +10V (Figure 5)
Charge Injection, Q(INJ.)
Minimum Off Isolation
Rejection Ratio, OIRR
Figure 6
f = 1MHz, RL = 100â¦,
CL ⤠5pF
(Figure 7, Note 1)
-
15 (Typ)
-
-
54 (Typ)
-
-
20 (Typ)
-
mV
-
50 (Typ)
-
dB
+Power Supply
VIN = 0V or VIN = 5V
1000
1000
2000
1000
1000
2000
µA
Quiescent Current, IV1
-Power Supply
Quiescent Current, IV2
1000
1000
2000
1000
1000
2000
µA
Minimum Channel to
One Channel Off
Channel Cross Coupling
Rejection Ratio, CCRR
-
54 (Typ)
-
-
50 (Typ)
-
dB
NOTES:
1. Pull Down Resistor must be ⤠2kâ¦.
2. Typical values are for design aid only, not guaranteed and not subject to production testing.
3. All channels are turned off by high â1â logic inputs and all channels are turned on by low â0â inputs; however 0.8V to 2.4V describes the
minimum range for switching properly. Peak input current required for transition is typically -120µA.
9-15
|
▷ |
German
Russian
Spanish
Italian
Polish
Chinese
Japanese
Korean
French
Portuguese