C9311DK Datasheet, PDF (4/6 Pages) Hamamatsu Corporation – Flat panel sensor High sensitivity, high-speed frame rate, high resolution

Flat panel sensor C9311DK
s System requirements
To operate C9311DK at full performance, the following system and peripherals are required.
· PC: IBM compatible PC running on Windows XP
· Digital frame grabber card: Monochrome 32 bits or more, pixel clock 33.3 MHz or more, LVDS interface synchronous signal (See
the frame grabber manual.)
· Power source: A.vdd = +5.0 ± 0.1 V (1800 mA), D.vdd = +5.0 ± 0.1 V (500 mA)
Please use a low noise series power supply. (Avoid using a switching power supply.) A optional power cable (terminated with
an DB-25SF-N plug at one end and open at the other end; 2 m; see Table 2.) and an earth cable (AWG 18; 4 m) comes supplied
with C9311DK. An optional frame grabber cable for interface with the 80-pin receptacle (see Table 1) on C9311DK is also
available for synchronous signal, video output and external control.
The voltages described above are specified at the flat panel sensor side. The impedance of the power cable attached with the
flat panel sensor is low enough but it causes 0.1 V approx. drop. Therefore the voltage at the power source side should be set
0.1 V higher than the voltage specified above. Install a noise filter on the AC power input line to prevent surges on the AC line.
The earth terminal must be connected to a stable earth point to eliminate noise from surroundings.
Table 1: Pin assignment of 80-pin receptacle
Pin No.
Signal
Pin No.
Signal
1
A_Data1+ (LSB)
41
B_Data1+ (LSB)
2
A_Data1- (LSB)
42
B_Data1- (LSB)
3
A_Data2+
43
B_Data2+
4
A_Data2-
44
B_Data2-
5
A_Data3+
45
B_Data3+
6
A_Data3-
46
B_Data3-
7
A_Data4+
47
B_Data4+
8
A_Data4-
48
B_Data4-
9
A_Data5+
49
B_Data5+
10
A_Data5-
50
B_Data5-
11
A_Data6+
51
B_Data6+
12
A_Data6-
52
B_Data6-
13
A_Data7+
53
B_Data7+
14
A_Data7-
54
B_Data7-
15
A_Data8+
55
B_Data8+
16
A_Data8-
56
B_Data8-
17
A_Data9+
57
B_Data9+
18
A_Data9-
58
B_Data9-
19
A_Data10+
59
B_Data10+
20
A_Data10-
60
B_Data10-
21
A_Data11+
61
B_Data11+
22
A_Data11-
62
B_Data11-
23
A_Data12+ (MSB)
63
B_Data12+ (MSB)
24
A_Data12- (MSB)
64
B_Data12- (MSB)
25
Reserved
65
Reserved
26
Reserved
66
Reserved
27
Reserved
67
Reserved
28
Reserved
68
Reserved
29
Reserved
69
Reserved
30
Reserved
70
Reserved
31
Reserved
71
Reserved
32
Reserved
72
Reserved
33
IntExt (TTL)
73
ExtTrgGrb (TTL)
34
Reserved
74
Reserved
35
Vsync+
75
bin0 (TTL)
36
Vsync-
76
Reserved
37
Hsync+
77
bin1 (TTL)
38
Hsync-
78
Reserved
39
Pclk+
79
GND
40
Pclk-
80
GND
Unless otherwise noted, signal level is LVDS.
80-pin receptacle: PCS-E80LMD made by Honda Tsushin Kogyo Co., Ltd.
Mating plug: PCS-E80FA made by Honda Tsushin Kogyo Co., Ltd.
Pins described “Reserved” are prepared for an extention of the future. Do not connect any signal or power or GND to this plug.
4