MC9S08SV16 Datasheet, PDF (1/40 Pages) Freescale Semiconductor, Inc – 8-Bit HCS08 Central Processor Unit (CPU)

Freescale Semiconductor
Data Sheet: Technical Data
Document Number: MC9S08SV16
Rev. 2, 7/2009
MC9S08SV16 Series
Covers: MC9S08SV16 and
MC9S08SV8
MC9S08SV16
32-Pin LQFP
873A-03
32-Pin SDIP
1376-02
Features:
• 8-Bit HCS08 Central Processor Unit (CPU)
– Up to 40 MHz CPU at 2.7 V to 5.5 V across temperature
range of –40 °C to 85 °C
– HC08 instruction set with added BGND instruction
– Support for up to 32 interrupt/reset sources
• On-Chip Memory
– Up to 16 KB flash read/program/erase over full
operating voltage and temperature
– Up to 1024-byte random-access memory (RAM)
– Security circuitry to prevent unauthorized access to
RAM and flash contents
• Power-Saving Modes
– Two low power stop modes; reduced power wait mode
– Allows clocks to remain enabled to specific peripherals
in stop3 mode
• Clock Source Options
– Oscillator (XOSC) — Loop-control Pierce oscillator;
crystal or ceramic resonator range of 31.25 kHz to
39.0625 kHz or 1 MHz to 16 MHz
– Internal Clock Source (ICS) — Internal clock source
module containing a frequency-locked-loop (FLL)
controlled by internal or external reference; precision
trimming of internal reference allows 0.2% resolution
and 2% deviation over temperature and voltage;
supporting bus frequencies up to 20 MHz
• System Protection
– Watchdog computer operating properly (COP) reset
with option to run from dedicated 1 kHz internal clock
source or bus clock
– Low-voltage detection with reset or interrupt; selectable
trip points
– Illegal opcode detection with reset
– Illegal address detection with reset
– Flash block protection
• Development Support
– Single-wire background debug interface
– Breakpoint capability to allow single breakpoint setting
during in-circuit debugging (plus two more breakpoints)
– On-chip in-circuit emulator (ICE) debug module
containing two comparators and nine trigger modes
• Peripherals
– IPC — Interrupt priority controller to provide hardware
based nested interrupt mechanism
– ADC — 12-channel, 10-bit resolution; 2.5 μs
conversion time; automatic compare function;
1.7 mV/°C temperature sensor; internal bandgap
reference channel; operation in stop; optional hardware
trigger; fully functional from 2.7 V to 5.5 V
– TPM — One 6-channel and one 2-channel
timer/pulse-width modulators (TPM) modules;
selectable input capture, output compare, or buffered
edge- or center-aligned PWM on each channel
– MTIM16 — One 16-bit modulo timer
– SCI — One serial communications interface module
with optional 13-bit break; LIN extensions
– SPI — One serial peripheral interface module in 8-bit
data length mode with a receiving data buffer hardware
match function
– IIC — Inter-integrated circuit bus module capable of
operation up to 100 kbps with maximum bus loading;
multi-master operation; programmable slave address;
interrupt-driven byte-by-byte data transfer; broadcast
mode; 10-bit addressing
– ACMP — Analog comparator with option to compare to
internal reference
– RTC — Real time counter
– KBI— 8-pin keyboard interrupt module with software
selectable polarity on edge or edge/level modes
• Input/Output
– 30 GPIOs including one output-only pin and one
input-only pin
• Package Options
– 32-pin SDIP
– 32-pin LQFP
This document contains information on a product under development. Freescale reserves the
right to change or discontinue this product without notice.
© Freescale Semiconductor, Inc., 2009. All rights reserved.