English
Language : 

FWLF1524P2YXX Datasheet, PDF (5/11 Pages) Finisar Corporation. – 4 Gigabit RoHS Compliant CWDM SFP Transceiver
FWLF1524P2yxx SFP Product Specification – April 2012
Finisar
IV. Optical Characteristics (TOP = -5 to 75 C, VCC = 3.1 to 3.5 Volts)
Parameter
Symbol Min Typ Max Unit Ref.
Transmitter
Output Opt. Power (Rate Select High)
Output Opt. Power (Rate Select Low)
Optical Wavelength
PO,RH
PO,RL
+1
+5 dBm 1
+1
+5 dBm 2
X-6.5 X X+6.5 nm 3
Spectral Width
1
nm 3
Optical Modulation Amplitude
OMA
290
uW 4
Optical Extinction Ratio (Rate Select High)
ER
4
dB
Optical Extinction Ratio (Rate Select Low)
ER
9
dB
Optical Rise/Fall Time = 4.25 Gb/s
tr/ tf
Optical Rise/Fall Time 2.125 Gb/s
tr/ tf
RIN
105
ps 5
160
ps 6
-118 dB/Hz
Deterministic Jitter Contribution = 4.25 Gb/s TX DJ
28.2
ps 7
Total Jitter Contribution = 4.25 Gb/s
TX TJ
59.8
ps
Deterministic Jitter Contribution 2.125 Gb/s TX DJ
56.5
ps 7
Total Jitter Contribution 2.125 Gb/s
TX TJ
119
ps
Receiver
Receiver Sensitivity = 4.25 Gb/s
RSENS4
29
-16.5
uW 8
dBm 9
Receiver Sensitivity = 2.125 Gb/s
RSENS2
15
-20.5
uW 8
dBm 9
Receiver Sensitivity = 1.06 Gb/s
RSENS1
15
-22.0
uW 8
dBm 10
Receiver Sensitivity = 1.25 Gb/s
Stressed RX sens. = 1.25 Gb/s
RSENS-GE
-22
-14.5
dBm 10
dBm
Average Received Power
Receiver Electrical 3dB cutoff freq.
RxMAX
0
1500
dBm
MHz 11
Receiver Electrical 3dB cutoff freq.
2500 MHz 12
Optical Center Wavelength
Return Loss
C
1450
12
1620 nm
dB
LOS De-Assert
LOS Assert
LOS Hysteresis
LOSD
LOSA
-30
0.5
-19 dBm
dBm
dB
Notes:
1. High Bandwidth Mode. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations.
2. Low Bandwidth Mode. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations.
3. Over case temperature of -5 to 75 °C. The Transmitter Center Wavelength “X” is as specified by the
customer. The current available wavelengths are: 1471, 1491, 1511, 1531, 1551, 1571, 1591, and 1611
nm. Please see the “Product Selection” section on page 2.
4. Equivalent extinction ration specification for Fibre Channel. Allows smaller ER at higher average
power
5. Unfiltered, 20-80% measured w/ a “00001111” pattern. Complies with FC 4x eye mask when filtered.
6. Unfiltered, 20-80% measured w/ a “00001111” pattern. Complies with IEEE 802.3 (Gig. E), FC 1x
and 2x eye masks when filtered.
7. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ
and DJ.
8. Measured with conformance signals defined in FC-PI-2 Rev. 10.0 specifications. Value in OMA.
Measured with PRBS 27-1 at 10-12 BER.
9. Represents sensitivity at minimum Extinction Ratio with rate select high. Measured with PRBS 27-1 at 10-12 BER.
Finisar Corporation April, 2012 Rev E
Page 5