GTLP10B320 Datasheet, PDF (6/12 Pages) Fairchild Semiconductor – 10-Bit LVTTL/GTLP Transceiver with Split LVTTL Port and Feedback Path

DC Electrical Characteristics (Continued)
Symbol
Test Conditions
Min
Typ
Max
(Note 7)
Units
I_CC
∆I_CC
(Note 9)
C_i
A or B Ports
or C Port
A Port and
Control Pins
Control Pins
and A Port
V_CC = 3.45V
Outputs HIGH
I_O = 0
Outputs LOW
V_I = V_CC/V_TT or GND
Outputs Disabled
V_CC = 3.45V,
One Input at V_CC
A or Control Inputs at V_CC or GND −0.6V
V_I = V_CC or 0
C Port
B Port
Note 7: All typical values are at V_CC = 3.3V and T_A = 25°C.
V_I = V_CC or 0
V_I = V_CC or 0
27
45
27
45
mA
27
45
2
mA
4.5
pF
6
9
Note 8: For conditions shown as Min, use the appropriate value specified under recommended operating conditions.
Note 9: This is the increase in supply current for each input that is at the specified TTL voltage level rather than V_CC or GND.
Note: GTLP V_REF and V_TT are specified to 2% tolerance since signal integrity and noise margin can be significantly degraded if these supplies are noisy. In
addition, V_TT and R_TERM can be adjusted beyond the recommended operating to accommodate backplane impedances other than 50Ω, but must remain
within the boundaries of the DC Absolute Maximum Ratings. Similarly, V_REF can be adjusted to optimize noise margin.
AC Operating Requirements
Over recommended ranges of supply voltage and operating free-air temperature, V_REF = 1.0V (unless otherwise noted).
Symbol
Test Conditions
Min
Max
f_MAX
Maximum Clock Frequency
150
t_WIDTH
Pulse Duration
LECLKAB, LECLKBC HIGH or LOW
3.0
t_SET
Setup Time
SAB = 0 A before LECLKAB↑
2.1
SBC = 0 B before LECLKBC↑
2.6
SAB = 1, SEL = 1, SBC = 0 A before LECLKBC↑
6.8
SAB = 1, SEL = 0, SBC = 0 A before LECLKBC↑
3.0
SAB = 1 A before LECLKAB↓
1.7
SBC = 1 B before LECLKBC↓
2.2
SAB = 1, SEL = 1, SBC = 1 A before LECLKBC↓
6.4
SAB = 1, SEL = 0, SBC = 1 A before LECLKBC↓
2.8
t_HOLD
Hold Time
SAB = 0 A after LECLKAB↑
2.0
SBC = 0 B after LECLKBC↑
1.6
SAB = 1, SEL = 1, SBC = 0 A after LECLKBC↑
−1.4
SAB = 1, SEL = 0, SBC = 0 A after LECLKBC↑
1.4
SAB = 1 A after LECLKAB↓
2.5
SBC = 1 B after LECLKBC↓
2.1
SAB = 1, SEL = 1, SBC = 1 A after LECLKBC↓
−1.0
SAB = 1, SEL = 0, SBC = 1 A after LECLKBC↓
1.6
Unit
MHz
ns
ns
ns
www.fairchildsemi.com
6