FXMA2102 Datasheet, PDF (6/16 Pages) Fairchild Semiconductor – Dual Supply, 2-Bit Voltage Translator / Buffer / Repeater / Isolator for I2C Applications

Application Notes
The FXMA2102 has open-drain I/Os and requires
external pull-up resistors on the four data I/O pins, as
shown in Figure 4. If a pair of data I/O pins (A_n/B_n) is not
used, both pins should be tied to GND (or both to V_CC).
In this case, pull-down or pull-up resistors are not
required. The recommended values for the pull-up
resistors (RPU) are 1 KΩ to 10 KΩ; however, depending
on the total bus capacitance, the user is free to vary the
pull-up resistor value to meet the maximum I²C edge
rate per the I²C specification (UM10204 rev. 03, June
19, 2007). For example, the maximum edge rate (30% -
70%) during fast mode (400 kbit/s) is 300 ns. If bus
capacitance is approaching the maximum 400 pF, lower
the RPU value to keep the rise time below 300 ns (Fast
Mode). Section 7.1 of the I²C specification provides an
excellent guideline for pull-up resistor sizing.
Theory of Operation
The FXMA2102 is designed for high-performance level
shifting and buffer / repeating in an I²C application.
Figure 1 shows that each bi-directional channel contains
two series-Npassgates and two dynamic drivers. This
hybrid architecture is highly beneficial in an I²C
application where auto-direction is a necessity.
For example, during the following three I²C protocol
events:
 Clock Stretching
 Slave’s ACK Bit (9^th bit = 0) following a Master’s
Write Bit (8^th bit = 0)
 Clock Synchronization and Multi Master
Arbitration
the bus direction needs to change from master to slave
to slave to master without the occurrence of an edge. If
there is an I²C translator between the master and slave
in these examples, the I²C translator must change
direction when both A and B ports are LOW. The
Npassgates can accomplish this task very efficiently
because, when both A and B ports are LOW, the
Npassgates act as a low resistive short between the two
(A and B) ports.
Due to I²C’s open-drain topology, I²C masters and
slaves are not push/pull drivers. Logic LOWs are “pulled
down” (I_sink), while logic HIGHs are “let go” (3-state). For
example, when the master lets go of SCL (SCL always
comes from the master), the rise time of SCL is largely
determined by the RC time constant, where R = R_PU and
C = the bus capacitance. If the FXMA2102 is attached
to the master [on the A port] in this example, and there
is a slave on the B port, the Npassgates act as a low
resistive short between both ports until either of the
port’s V_CC/2 thresholds are reached. After the RC time
constant has reached the V_CC/2 threshold of either port,
the port’s edge detector triggers both dynamic drivers to
drive their respective ports in the LOW-to-HIGH (LH)
direction, accelerating the rising edge. The resulting rise
time resembles the scope shot in Figure 5. Effectively,
two distinct slew rates appear in rise time. The first slew
rate (slower) is the RC time constant of the bus. The
second slew rate (much faster) is the dynamic driver
accelerating the edge.
If both the A and B ports of the translator are HIGH, a
high-impedance path exists between the A and B ports
because both the Npassgates are turned off. If a master
or slave device decides to pull SCL or SDA LOW, that
device’s driver pulls down (I_sink) SCL or SDA until the
edge reaches the A or B port V_CC/2 threshold. When
either the A or B port threshold is reached, the port’s
edge detector triggers both dynamic drivers to drive their
respective ports in the HIGH-to-LOW (HL) direction,
accelerating the falling edge.
Figure 5. FXMA2102 Waveform C: 600 pF, R_PU: 2.2 K
© 2010 Fairchild Semiconductor Corporation
FXMA2102 • Rev. 1.0.5
6
www.fairchildsemi.com