RHFAC245D03V Datasheet, PDF (3/25 Pages) List of Unclassifed Manufacturers – STANDARD MICROCIRCUIT DRAWING

1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
Descriptive designator
Terminals
Package style
R
GDIP1-T20 or CDIP2-T20
20
S
GDFP2-F20 or CDFP3-F20
20
X
See figure 1
20
Z
GDFP1-G20
20
2
CQCC1-N20
20
Dual-in-line
Flat pack
Flat pack
Flat pack with gullwing
Square leadless chip carrier
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,
appendix A for device class M.
1.3 Absolute maximum ratings. 1/ 2/ 3/
Supply voltage range (VCC) .................................................................................. -0.5 V dc to +7.0 V dc
DC input voltage range (VIN) ................................................................................ -0.5 V dc to VCC + 0.5 V dc
DC output voltage range (VOUT) ........................................................................... -0.5 V dc to VCC + 0.5 V dc
Clamp diode current (IIK, IOK) ............................................................................... ±20 mA
DC output current (per output pin) (IOUT) .............................................................. ±50 mA
DC VCC or GND current (per output pin) (ICC, IGND) .............................................. ±50 mA 4/
Maximum power dissipation (PD) ......................................................................... 500 mW
Storage temperature range (TSTG) ....................................................................... -65°C to +150°C
Lead temperature (soldering, 10 seconds):
Case outline X ................................................................................................. +260°C
Other case outlines except case X .................................................................. +245°C
Thermal resistance, junction-to-case (θJC) ........................................................... See MIL-STD-1835
Junction temperature (TJ) .................................................................................... 175°C 5/
1.4 Recommended operating conditions. 2/ 3/ 6/
Supply voltage range (VCC) .................................................................................. +2.0 V dc to +6.0 V dc
Input voltage range (VIN) ...................................................................................... 0.0 V dc to VCC
Output voltage range (VOUT)................................................................................. 0.0 V dc to VCC
Input rise or fall time rate (∆t/∆v):
VCC = 3.6 V to 5.5 V ......................................................................................... 0 to 8 ns/V
Case operating temperature range (TC) ............................................................... -55°C to +125°C
1.5 Radiation features.
Device type 02:
Maximum total dose available (dose rate = 50 – 300 rads (Si)/s) .................... 300 krads (Si) 7/
No SEL occurs at effective LET (see 4.4.4.2) .................................................. ≤ 93 MeV-cm²/mg 7/
1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
2/ Unless otherwise noted, all voltages are referenced to GND.
3/ The limits for the parameters specified herein shall apply over the full specified VCC range and case temperature range
of -55°C to +125°C.
4/ For devices with multiple VCC or GND pins, this value represents the total VCC or GND current.
5/ Maximum junction temperature shall not be exceeded except for allowable short duration burn-in screening conditions in
accordance with method 5004 of MIL-STD-883.
6/ Operation from 2.0 V dc to 3.0 V dc is provided for compatibility with data retention and battery back-up systems. Data
retention implies no input transition and no stored data loss with the following conditions: VIH ≥ 70% VCC, VIL ≤ 30% VCC,
VOH ≥ 70% VCC @ -20 µA, VOL ≤ 30% VCC @ 20 µA.
7/ These limits were obtained during technology characterization and qualification, and are guaranteed by design or process,
but not production tested unless specified by the customer through the purchase order or contract.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
H
5962-87758
SHEET
3