PI33XX-X0 Datasheet, PDF (28/42 Pages) List of Unclassifed Manufacturers – 8V to 36Vin Cool-Power ZVS B uck Regulator Family

PI33XX-X0
PI3305-X0 (15.0 Vout) Electrical Characteristics
Specifications apply for -40C < T_J < 125C, Vin =24V, L1=230nH (Note 1) unless other conditions are noted.
Parameter
Symbol
Min Typ Max Units Conditions
Input Specifications
Input Voltage
Input Current
Input Current At Output Short
(fault condition duty cycle)
V_{IN_DC}
I_{IN_DC}
20.4 24
36
5.15
V Note 7.
A
Vin = 24V, T_C = 25°C,
Iout=8A
I_{IN_Short}
20
mA
Input Quiescent Current
I_{Q_VIN}
2
2.5
mA
Disabled
Enabled (no load)
Input Voltage Slew Rate
Output Specifications
V_{IN_SR}
1
V/μs
Output Voltage Total Regulation
Output Voltage Trim Range
V_{OUT_DC}
14.78 15.0 15.23
10.0 15
16
V Note 2.
V Note 3. Note 7.
Line Regulation
Load Regulation
Output Voltage Ripple
∆V_OUT(∆V_IN)
0.1
% @25°C, 20.4V<Vin<36V
∆V_OUT(∆I_OUT)
0.1
% @25°C, 0.5A<Iout<8A
V_{OUT_AC}
60
mVp-p
Iout=4A, Cout=4x22μF,
20MHz BW Note 4.
Continuous Output Current Range
Current Limit
Protection
I_{OUT_DC}
I_{OUT_CL}
8
A Note 5. Note 7.
9
A
UVLO Start Threshold
UVLO Stop Threshold
UVLO Hysteresis
OVLO Threshold
OVLO Hysteresis
UVLO/OVLO Fault Delay Time
UVLO/OVLO Response Time
Output Over Voltage Protection
Over-Temperature Fault Threshold
Over-Temperature Restart
Hysteresis
V_{UVLO_START}
V_{UVLO_STOP}
V_{UVLO_HYS}
V_OVLO
V_{OVLO_HYS}
t_{f_DLY}
t_f
V_OVP
T_OTP
T_{OTP_HYS}
18.4
17.4
4
37
130
19.4
18.4
5
38.4
0.77
128
500
20
135
30
20.4
V
19.4
V
6
%
V
V
Cycles
ns
Number of the
switching frequency
cycles
+1% overdrive
% Above Vout
140
°C
°C
Note 1: All parameters reflect regulator and inductor system
performance. Measurements were made using a standard PI33XX
evaluation board with 3x4” dimensions and 4 layer, 2oz copper.
Refer to inductor pairing table within Application Description
section for specific inductor manufacturer and value.
Note 2: Regulator is assured to meet performance specifications
by design, test correlation, characterization, and/or statistical
process control.
Note 3: Output current capability may be limited and other
performance may vary from noted electrical characteristics when
switching frequency or Vout is modified.
Note 4: Refer to Output Ripple plots.
Note 5: Refer to Load Current vs. Ambient Temperature curves.
Note 6: Refer to Switching Frequency vs. Load current curves.
Note 7: Minimum 5V between Vin-Vout must be maintained or a
minimum load of 1mA required.
vicorpower.com
800 735.6200
Rev 1.4
11/2012
Cool-Power^®
Page 28 of 42